LAVAZZA Magystra LB 2600 AUS Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 44

LAVAZZA Magystra LB 2600 AUS Скачать руководство пользователя страница 15

15

EN

PREPARING THE MACHINE

FIRST POWER-ON

Press the main switch and put it in position

[ON]

.

The display will show the machine is turned on.

Arrange a cup beneath the nozzles.

Open the dispenser door by unlocking the lock with

the proper key.

Whenever you open the door, a special switch will

power off the electric installation of the equipment.

Fit the service key into the door switch to power the sys-

tem.

The vending machine is supplied and running to

all effects . The mobile parts of the coffee group

will be handled; act extremely carefully .

The start-up test messages appear on the display in

a sequence:

Lift the top cover and remove the water tank up-

wards, using the proper handle.

Rinse the tank before use. Fill the water tank using

only non carbonated fresh drinking water.

A red float inside the tank indicates the maximum

filling level .

LB2600 REV.1.17

04-03-2016

TEST

LAVAZZA

TEST

CHECK COFFEE

BREWER

REFILL

WATER

«
...
13
14
15
16
17
...
»

Содержание Magystra LB 2600 AUS













































Отзывы:

Нет отзывов