![background image](http://html1.mh-extra.com/html/launch/x-631-plus/x-631-plus_user-manual_3852883019.webp)
LAUNCH X-631/X-631+ Wheel Aligner Operation Instructions
4-4
z
Specified rim and tire
z
The brake pedal depressor is installed
z
Counterweight the whole vehicle
according to the normal driving
conditions. Adjust the seats to the
middle positions and fill the gasoline
tank full.
2). If the measured values are beyond the tolerance
range, it indicates that the vehicle is faulty, and the
faults must be eliminated before performing the ride
height measurement.
3). For the vehicle with air shock absorbers, please
pull out the security device of the air feeding
equipment to prevent the vehicle from being
adjusted up and down.
4). The sandbags and height measurement meter are
not delivered with the instrument, users should
prepare them by themselves.
Run-out Compensation
This function is to reduce the error caused by the
distortion of the wheel rim and tire. It is advisable to
select this function to ensure measuring accuracy.
The interface is as shown in Fig.4.10.
Fig.4.10
[Icon for the level status of probe rod]: To indicate the
level status of the present probe rod. Green indicates
the probe rod is level and red indicates not level.
[Previous]: To return to the previous operating
procedure.
Operating procedures:
1.
Keep the vehicle wheels on straight-ahead
positions, fix the steering wheel with the steering
wheel holder, remove the brake pedal depressor
to keep the wheels can be freely rotated.
2.
Install four wheel clamps and probe rods, and
then adjust each probe rod level respectively.
3.
According to the prompts on the screen, start the
run-out compensation operation for LF wheel.
Adjust LF probe rod level, and click [NEXT] after
finished.
4.
According to the prompts on the screen, turn LF
wheel by 180°. Adjust LF probe rod level, and
click [NEXT] after finished.
5.
According to the prompts on the screen, turn LF
wheel by 360°. Adjust LF probe rod level, and
click [NEXT] after finished.
6.
According to the prompts on the screen, perform
the run-out compensation operation for RF, RR
and LR wheel respectively.
7.
Put down the vehicle body, keep the four wheels
on the ground. Shake the vehicle body, keep four
wheels cling to the ground, the run-out
compensation operation is finished (The
interface displays the values of run-out
compensation).
Caution:
1.
Before performing run-out compensation
operation, be sure to fix the steering wheel
according to the requirements, in order to avoid
the wheels' swing to left or right when performing
run-out compensation operation, causing the
inaccurate run-out compensation.
2.
You are required to swing the vehicle tires when
performing the run-out compensation operation.
Keep each probe rod to be at rest comparatively
and level (if some probe rod is not level during
operating, the system cannot perform the next
operation until the probe rod is adjusted level).
3.
If the left wheels and right wheels of some
vehicles are linked (i.e. when left wheel rotates,
the right wheel rotates, too), and you want to
perform run-out compensation operation, you
must hold the right (left) wheel when you rotate
the left (right) wheel, and you should notice that
force from you hands must be balanced (in order
to avoid wheel's swing to left and right and
causing inaccurate run-out compensation).
Meanwhile you should check if the probe rods
are level or not. If not, it is necessary to adjust
the probe rods level by the way of rotating the
wheels. You should note that the probe rods
mustn't be adjusted level by the way of loosing
them.
4.
If the second-time lift can put up the front and
rear axles at the same time, the front and rear
axles should be put up at the same time when
performing the run-out compensation operations;
if the second-time lift can only put up one axle at
a time, please put up the front axle individually
when performing the front wheel run-out
compensation operations, and put up the rear
axle individually when performing the rear wheel
run-out compensation operations.
5.
Three types of run-out compensation operation
modes (90°, 180° and rolling run-out
compensation) can be set on the interface of
[System Management]-[System Setting].
180°run-out compensation mode is a standard
one. It is with high accuracy, and cross reference
between front and rear probe rod is necessary
The icon for the level status
of probe rod
Previous
Содержание X-631 Plus
Страница 1: ......