manualshive.com logo in svg
background image

LAUNCH                                                                                                                            Injector Cleaner & Tester User’s Manual 

 

i

 

Trademark Information 

 

LAUNCH

 is a registered trademark of LAUNCH TECH. 

CO., LTD. (LAUNCH for short) in China and other 
countries. All other LAUNCH trademarks, service marks, 
domain names, logos, and company names referred to in 

this manual are either trademarks, registered trademarks, 
service marks, domain names, logos, company names of 
or are otherwise the property of LAUNCH or its affiliates. In 
countries where any of the LAUNCH trademarks, service 
marks, domain names, logos and company names are not 

registered, LAUNCH claims other rights associated with 
unregistered trademarks, service marks, domain names, 
logos, and company names. Other products or company 
names referred to in this manual may be trademarks of 
their respective owners. You may not use any trademark, 

service mark, domain name, logo, or company name of 
LAUNCH or any third party without permission from the 
owner of the applicable trademark, service mark, domain 
name, logo, or company name. You may contact LAUNCH 
by visiting Launch at http://www.cnlaunch.com, or writing to 

LAUNCH Industrial Park, North Wuhe Avenue, 
Banxuegang Industrial Park, Longgang Dist., Shenzhen, 
P.R. China, to request written permission to use Materials 
on this manual for purposes or for all other questions 
relating to this manual.   

 

Copyright Information 

 

Copyright © 2000 by LAUNCH TECH. CO., LTD. All rights 
reserved. No part of this publication may be reproduced, 

stored in a retrieval system, or transmitted in any form or 
by any means, electronic, mechanical, photocopying, 
recording or otherwise, without the prior written permission 
of LAUNCH. The information contained herein is designed 
only for the use of this unit. LAUNCH is not responsible for 
any use of this information as applied to other units.   

 

Neither LAUNCH nor its affiliates shall be liable to the 
purchaser of this unit or third parties for damages, losses, 
costs, or expenses incurred by purchaser or third parties 
as a result of: accident, misuse, or abuse of this unit, or 

unauthorized modifications, repairs, or alterations to this 
unit, or failure to strictly comply with LAUNCH operating 
and maintenance instructions.   

 

LAUNCH shall not be liable for any damages or problems 

arising from the use of any options or any consumable 
products other than those designated as Original LAUNCH 
Products or LAUNCH Approved Products by LAUNCH.     

 

General Notice 

 

Other product names used herein are for identification 

purposes only and may be trademarks of their respective 
owners. LAUNCH disclaims any and all rights in those 
marks.  

Disclaimer 

 

z

 

To take full advantage of the unit, you should be 
familiar with the engine. 

z

 

All information, illustrations, and specifications 
contained in this manual are based on the latest 
information available at the time of publication. The 

manufacturer resume the right of modify this manual 
and the machine itself with no prior notice.

 

 

This unit is made for the purpose of persons who have 
special techniques and certifications.   

 

Safety Precautions 

 

Read all service procedures and precautions, installation 

instructions and equipment operating manuals thoroughly. 
Failure to observe these precautions, or the improper use 
of equipment, could result in property damage, serious 
injury or death. Never allow improperly trained personnel 
to perform these procedures or operate the equipment. 

 

z

 

Read the operating instructions before attempting to 

operate the unit. Keep this manual with the unit at 
all times.   

z

 

Care must be taken as burns can occur from 

touching hot parts of the equipment or in the 

engine. 

z

 

Do not operate equipment with a damaged cord or if 

the equipment has been dropped or damaged until 
it has been examined by qualified service 
personnel. 

z

 

Do not hang cords over the edge of the table, bench 

or counter, or come in contact with hot manifolds or 
moving fan blades. 

z

 

If an extension cord is needed, a cord with a rated 

current equal to or greater than that of the 

equipment should be used. Cords rated for lower 
current than that of the equipment may overheat.   

z

 

Always unplug equipment from electrical outlet 

when the machine is not in use. Never pull the cord 
when unplugging from the outlet. 

z

 

Make sure the equipment cools down completely 

before putting it away. Loop cord loosely around the 
equipment when storing. 

z

 

To protect against risk of fire, do not operate the 

equipment in the vicinity of open container 

containing flammable liquid (gasoline). 

z

 

Make sure that the unit is in the well-ventilation area 

when operating the fuel engine. 

z

 

Keep lighted cigarettes, sparks, flames or other 
ignition sources away from fuel systems at all times.   

Содержание CNC-602A

























Отзывы: