WARNING!
NOTICE:
WATER GAUGE GLASS
READ ALL WARNINGS AND
INSTRUCTIONS BEFORE
PERFORMING INSTALLATION
OR MAINTENANCE.
I-5334-00 REV. H
SAFETY GLASSES AND GLOVES
SHOULD BE WORN AT ALL TIMES
WHEN WORKING WITH OR
EXAMINING WATER GAUGE GLASS
AND CONNECTIONS.
IMPROPER INSTALLATION OR
MAINTENANCE OF GAUGE GLASS
AND CONNECTIONS CAN CAUSE
IMMEDIATE OR DELAYED BREAK-
AGE RESULTING IN BODILY INJURY
AND/OR PROPERTY DAMAGE.
WATER GAUGE GLASS
DO's
DO verify proper gauge has been supplied.
DO examine gauge glass and packings carefully
for damage before installation.
DO install protective guards and utilize
automatic ball checks where necessary to
help prevent injury in case of glass
breakage.
DO inspect the gauge glass daily, keep
maintenance records, and conduct routine
replacements.
DO protect glass from sudden changes in
temperatures such as drafts, water spray,
etc.
MAINTENANCE
Examine the gauge glass regularly for any signs
of clouding, scratching, erosion, or corrosion.
The glass should be inspected daily until the
need for replacement becomes apparent. This
will help establish the routine inspection and
routine replacement schedules.
CLEANING
Use commercial non-abrasive glass cleaners to
keep the glass clean. Use diluted acids such as
Hydrochloric (muriatic) acid when regular
cleaners do not seem to work. Do not use wire
brushes or any other abrasive materials which
could scratch the glass.
INSPECTION
Examine the surface of the glass for scratches,
corrosion, chips, cracks, surface flaws, or nicks.
To do this, shine a very bright concentrated
light at an angle of about 45 degrees. A
defective glass will glisten as the light strikes
imperfections. Glass which appears cloudy or
roughened,will not respond to cleaning, and
should be replaced.
STORING
Keep gauge glass in original packaging until
ready to install.
PAGELAND, SC 29728
1418 S. PEARL ST.
TELEPHONE (704) 841-6000
www.apollovalves.com
Manufactured by Conbraco Industries, Inc.
This product contains chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm. (California
law requires that this warning be given to the consumers in the State
of California).
U.S. SAFE DRINKING WATER ACT WARNING:
It is illegal to use products that contain lead for potable water services
(Water intended for human consumption) in the United States.
TOP GAUGE FITTING
VESSEL
WALL
GAUGE
GLASS
GLASS
PACKING
NUT
GLASS
PACKING
GUARD
ROD
PACKING
GLAND
(OR
FRICTION
WASHER)
BOTTOM
GAUGE
FITTING
DRAIN
VALVE
WARNING!
VALVE MUST BE USED IN THE FULLY
OPEN POSITION FOR PROPER
OPERATION OF BALL CHECK. FAILURE
TO DO SO COULD RESULT IN BODILY
INJURY AND/OR PROPERTY DAMAGE.
BALL
CHECK
VALVE
ASME
AUTOMATIC
BALL
CHECK
VALVE
I-5334-00 REV. H
NOTE: NOT ALL WATER GAUGES ARE
EQUIPPED WITH BALL CHECK VALVES
Only properly trained personnel should install and
maintain water gauge glass and connections.
Remember to wear safety gloves and glasses
during installation. Before installing, make sure
all parts are free of chips and debris.
1. Apply thread sealant or tape to pipe threads.
Install top gauge fitting (fitting without a drain
valve) into the uppermost tapping. Wrench
tighten the fitting until it is snug and the glass
outlet is pointing at five o'clock (about 1/8
turn from its final downward vertical position).
2. Install the bottom gauge fitting (the fitting with
a drain valve) until it is snug and the glass
outlet is pointing directly upward.
3. Remove glass packing nut, friction washer (or
packing gland, depending on the model),and
glass packing from each gauge fitting. Slide
the packing nut, then friction washer or packing
gland, then and glass packing onto each end of
glass.
4. Gently insert one end of the glass into the top
gauge fitting. Keeping the glass inside the top
fitting, gently rotate the top gauge fitting
clockwise until vertically aligned with the
bottom gauge fitting, then insert glass into
bottom fitting until glass bottoms out on the
shoulder inside the bottom fitting.
5. Carefully raise glass about 1/16" and slide
lower glass packing down until the glass
packing contacts the lower gauge fitting. DO
NOT allow the glass to remain in contact with
any metal!
6. Carefully slide upper glass packing up as far as
possible.
7. Hand tighten both glass packing nuts, then
tighten 1/2 turn more by wrench. Tighten only
enough to prevent leakage. DO NOT OVER
TIGHTEN! If any leakage should occur,
tighten slightly, a quarter turn at a time,
checking for leakage after each turn.
WASHER
WATER GAUGE & GAUGE GLASS INSTALLATION GUIDE
20100, 20200, 20300, 20400, 20600, 20700, 20800, 21100, 21200, 22000, 22100, 22200, 23400,
23600, 24300, 24400, 24600, 24700, 24800, 25200, 25400, 25500, 25600, 20LF SERIES
DO NOT's
DO NOT use the glass if it contains any chips
or any other visible signs of damage.
DO NOT reuse any tubular glass or glass
packings.
DO NOT subject gauge glass to bending or
torsional stresses.
DO NOT over tighten glass packing nuts.
DO NOT allow glass to touch any metal
parts.
DO NOT exceed the recommended pressure of
the gauge or gauge glass.
DO NOT clean the gauge or gauge glass while
pressurized or in operation.
