background image

Form 

W01-17

LATTNER BOILER LIMITED WARRANTY 

A Lattner boiler shell is guaranteed to be constructed in accordance with the ASME Code.  An independent 
ASME boiler inspector inspects the construction of each boiler and:  (1) checks mill test reports on all 
materials used to ensure that the chemical and physical analysis of such materials complies with the ASME 
Code; (2) inspects each boiler shell during construction to see that workmanship complies with the Code; 
and (3) witnesses the final hydrostatic test and then places the ASME stamp on the boiler shell and signs an 
ASME data report certifying the boiler is ASME approved. 

Lattner warrants the boiler and any other equipment of its manufacture to be free from defects in material 
and workmanship for one (1) year from the date of shipment from the factory, provided the boiler is operated 
under the normal use and service for which it was intended, and only if the boiler has been properly installed 
by a qualified technician in accordance with but not limited to ASME, ANSI, and NFPA Codes and applicable 
local, state, and national codes. 

Lattner’s obligation under this Warranty is limited, at Lattner’s option, to replacing or repairing any defective 
part of the boiler or other equipment it manufactures.  No allowance will be made for labor, transportation, or 
other charges incurred in the replacement or repair of defective parts.  Merchandise not manufactured by 
the Company, supplied in one piece or in component assemblies, is not covered by the above warranty, but 
the Company will give the Purchaser the benefit of such adjustment as it can make with the manufacturer of 
such items. 

Lattner shall not be liable for special, indirect, or consequential damages.  Lattner shall not be liable for any 
loss or damage resulting, directly or indirectly, from the use or loss of use of the boiler.  This exclusion from 
liability includes the Purchaser’s expenses for downtime or for making up downtime, damages for which the 
Purchaser may be liable to other persons, or damages to property. 

The remedies set forth in this Warranty are exclusive, and the liability of Lattner with respect to any contract 
or sale shall not exceed the cost of repair or replacement of the boiler or other equipment manufactured by 
Lattner. 

The above Warranty shall not apply to any boiler or other equipment manufactured by Lattner which: 

1)

has been repaired or altered without Lattner’s written consent;

2)

has been altered in any way so as, in the judgment of Lattner, to adversely affect the stability

 

or reliability of the boiler;

3)

has been subject to improper water treatment, scale, corrosion, misuse, negligence, or

 

accident;

4)

has not been operated in accordance with Lattner’s printed instructions or specifications;

5)

has been operated under conditions more severe than or otherwise exceeding those set forth

 

in the specifications for such boiler; or

6)

has not been properly installed by a qualified technic

ian

 in accordance with but not limited to

 

ASME, ANSI and NFPA Codes and all applicable local, state and national codes.

THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR 
IMPLIED.  LATTNER MAKES NO WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR ANY 
PARTICULAR PURPOSE. 

Purchaser must notify Lattner of a breach of Warranty within thirty (30) days after discovery thereof, but not 
later than the one-year guarantee period; otherwise, such claims shall be deemed waived.  No allowance 
will be granted for any repairs or alterations made by Purchaser without Lattner’s prior verbal or written 
consent.  Items returned to Lattner must be accompanied by a factory-supplied return goods authorization 
(RGA).  

Such authorization may be obtained by calling the factory at 319/366-0778 or by writing to 

P.O. Box 1527, Cedar Rapids, IA 52406. 

Lattner neither assumes nor authorizes any person to assume for it any other liability in connection with the 
sale or use of the boiler or other equipment manufactured by Lattner, and there are no oral agreements or 
warranties collateral to or affecting this Agreement. 

LATTNER BOILER COMPANY 

Cedar Rapids, IA USA 

Содержание WLF 9.5 HP
































































Отзывы: