Lattice Semiconductor ispLever Core Multi-Channel DMA Controller Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 29

Lattice Semiconductor ispLever Core Multi-Channel DMA Controller Скачать руководство пользователя страница 25

Lattice Semiconductor

Multi-Channel DMA Controller User’s Guide

25

Appendix for ispXPGA

®

FPGAs

Table 20. Performance and Resource Utilization

1

Supplied Netlist Configurations

The Ordering Part Number (OPN) for all configurations of this core in ispXPGA devices is DMA-MC-XP-N2.
Table 21 lists the Lattice-specific netlists that are available in the Evaluation Package, which can be downloaded
from the Lattice web site at www.latticesemi.com.

Table 21. Core Configuration

You can use the IPexpress software tool to help generate new configurations of this IP core. IPexpress is the Lattice
IP configuration utility, and is included as a standard feature of the ispLEVER design tools. Details regarding the
usage of IPexpress can be found in the IPexpress and ispLEVER help system. For more information on the
ispLEVER design tools, visit the Lattice web site at: www.latticesemi.com/software.

Mode

Name of

Parameter File

LUT4

2

ispXPGA

PFUs

2

Registers

sysMEM

EBRs

I/O

f

MAX

(MHz)

8237

dma_mc_xp_2_001.lpc

1450

432

562

N/A

58

58

Non-8237

dma_mc_xp_2_002.lpc

3487

1072

1181

N/A

124

66

1. Performance and utilization characteristics are generated using LFX1200B-05F900C in Lattice ispLEVER 3.x software. The evaluation ver-

sion of this IP core only works on this specific device density, package, and speed grade.

2. PFU is a standard logic block of some Lattice devices. For more information, check the data sheet of the device.

Name of

Parameter File

Number of Channels

Data Bus Width

Address Bus Width

Word Count Width

8237 Mode

dma_mc_xp_2_001.lpc

4

8

16

16

Non-8237 Mode

dma_mc_xp_2_002.lpc

4

32

32

16

«
...
23
24
25
26
27
...
»

Содержание ispLever Core Multi-Channel DMA Controller






























Отзывы:

Нет отзывов