Lassco Wizer Spinnit FM 2 Скачать руководство пользователя

Страница: 2 / 16

Table Of Contents

1 - Introduction

1.1

1.2

1 - Introduction

1.1 - Your New FM-2 Paper Drill

1.2 - Shipping Damage Inspection

Remove the machine from the carton and inspect for

any shipping damage. If any damage is present, report

the damage to the carrier immediately; failure to do so

may void any warranties.

Page 01

Page 01

Your New FM-2 Paper Drill...................

Shipping Damage Inspection...............

2 - Safety

2.1

2.2

2.3

Page 02

Page 03

Page 04

Safety Instructions................................

Warning Labels.....................................

Grounding Instructions.........................

3 - Setting Up Your Machine

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

Page 05

Page 06

Page 07

Page 08

Loose Items Inventory..........................

Accessories Warning............................

Uncrating and Removing From the

Pallet....................................................

Installing the Leveling Feet..................

Attaching the Paper Side Stops...........

Attaching the Chip Bag........................

Choosing and Installing the Pattern

Bar.......................................................

Electrical Instructions...........................

4 - Operation

4.1

4.2

4.3

4.4

4.5

4.6

4.7

Page 09

Page 10

Page 11

Page 12

Protective Guard..................................

Drill Bit Removal and Installation.........

Adjusting the Table Height...................

Adjusting the Back-Gauge Assembly...

Traversing the Table.............................

Drilling Procedures...............................

Tips on Drilling......................................

5 - Maintenance

5.1

5.2

Page 13

Safety....................................................

Annual Lubrication................................

6 - Trouble Shooting Guide

6.1

Page 14

Determining the Cause and Correction

to Certain Problems..............................

Thank you for your purchase of the Spinnit FM-2 Paper

Drill.

We ask that you take a moment to fill in the serial

number and other information on the front cover of the

manual. Please keep this manual as a reference for

future use.

For parts and service, please contact the Lassco-Wizer

Dealer from whom you purchased the machine. If you

require assistance in locating a Lassco-Wizer Dealer

please contact our customer service department at 585-

436-1934. Please have the model of your machine and

the serial number when you call.

If you wish to write to us, send correspondence to:

Lassco-Wizer

Attn: Customer Service

485 Hague Street

Rochester, NY 14606

Содержание Spinnit FM 2

















Результаты поиска

Содержание Spinnit FM 2

Отзывы:

Похожие инструкции для Spinnit FM 2

Бренды по названию

Популярные бренды

Lassco Wizer Spinnit FM 2, Руководство пользователя

Результаты поиска

Содержание Spinnit FM 2

Отзывы:

Похожие инструкции для Spinnit FM 2

Бренды по названию

Популярные бренды