NEW 10/20
2
T38400_T38415ES
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
CAUTION
•
AVOID
the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these devices may overheat
and cause a fire hazard.
•
DO NOT
route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire hazard.
•
ALWAYS
place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
•
NEVER
insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
•
DO NOT
block, cover or obstruct air flow to or from the Fan while in operation.
•
DO NOT
use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may create a shock hazard.
•
DO NOT
run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances.
Arrange cord away from traffic area and where it will not be tripped over.
•
NEVER
use a single extension cord to operate more than one Fan or other electrical device.
•
DO NOT
use this Fan if it has been damaged or is not functioning properly.
• Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs, move the Fan to
another location.
• Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.
•
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008)
. This Fan is not suitable for use in agricultural facilities including
areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or
local codes or standards relating to electrical requirements for agricultural buildings.
•
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008)
. This Fan is not suitable for use in hazardous locations. Please refer
to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for hazardous locations.
Models T38400/T38415
Lasko Products, LLC
820 Lincoln Avenue
West Chester, PA
19380
www.lasko.com
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes
and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.
“NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and the receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.”
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT
use this Fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints, gasoline, varnishes,
floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the containers for these products!
ALWAYS
be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet and create
a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition should be replaced by a
qualified electrician.
ALWAYS
unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means of disconnecting
power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the Fan when not in use.
BE CERTAIN
that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The
Blue Plug
™
on your Lasko Fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed or tampered
with. To reduce the risk of fire, electric shock and personal injury,
DO NOT
attempt to remove, replace, repair or tamper with the originally sup-
plied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.
THIS FAN HAS A POLARIZED PLUG
(one blade is wider than the other). This plug is designed to fit into the outlet only one way. Match the wide
blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety feature. If the plug does not fit in the outlet, con-
sult a qualified electrician. The outlet may need to be replaced.
NEW 10/20
7
T38400_T38415ES
1 Cuerpo
3 Base de Soporte A
4 Base de Soporte B
2 Control Remoto
Controles
Partes Incluidas
Ensamblaje
Botón de Temporizador
El temporizador se puede configurar para 8 horas.
Continúe pulsando el Botón del Temporizador para
llegar a la configuración de tiempo deseada.
Botón de Oscilación
Presione el Botón de Oscilación para iniciar
y detener la función de oscilación.
Botón de Encendido
ENCENDIDO/APAGADO el Ventilador
presionando el Botón de Encendido.
Botón de Velocidad
La velocidad del ventilador se puede
ajustar a 1, 2, 3, o 4.
2. Alinee la
Montura de la Base de
Apoyo
con la
Cuerpo.
1. Empuje a los jefes en la
Base de
Soporte B
en las ranuras del jefe
en la
Base de Soporte A.
3. Sostenga la
Cuerpo
en su lugar mientras gira
la
Montura de la Base de Apoyo
en el sentido
de las agujas del reloj hasta que deje de girar
y encaje en su lugar.
1
4
3
2
