Rev. C 2/13
2
6405ES
7
6405ES
Rev. C 2/13
FUNCIONAMIENTO
(Figura 1)
1. Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2. Coloque el Calefactor sobre una superficie firme y plana.
Los tacos de plástico o hule, tales como las patas de esta unidad, pueden pegarse a la superficie de los muebles y/o a los pisos de
madera. La unidad podría dejar un residuo capaz de oscurecer, manchar o dejar marcas permanentes en el acabado de ciertas superficies
de muebles, incluyendo superficies de madera y/o pisos de madera.
3. Conecte el cable a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el tomacorriente.
Cuando los enchufes quedan flojos dentro de los tomacorrientes, podrían deslizarse parcial o completamente fuera del
tomacorriente con el menor movimiento del cable adosado. Los tomacorrientes en este estado podrían sobrecalentarse y
representar un peligro de incendio grave; si queda cubierto por una cortina o tela, el peligro de incendio es todavía mayor.
4.
Cuando el Calefactor se conecte por primera vez, se oirá un “bip” indicando que hay electricidad en la unidad.
5.
ENCIENDA el Calefactor oprimiendo el
Botón de Encendido
.
6.
Cuando se lo encienda por primera vez
, el Calefactor estará en calor
Alto
(1500 vatios) en
Máx
. (La luz Alta estará encendida
permanentemente y la luz de Máximo estará titilando).
7. Oprima el
Botón de Encendido
una vez más y el Calefactor estará en Calor
Bajo
, indicado por la luz permanente junto a
Bajo
. La luz
de Máximo estará titilando.
8. Oprimir el
Botón de Encendido
por tercera vez APAGARÁ el Calefactor.
Función de Oscilación
Presionar el
Botón de Oscilación
(OSC)
permitirá al Calefactor oscilar hacia atrás y hacia delante. Para detener la oscilación, oprima
el
Botón de Oscilación
(OSC)
una vez más.
Función de Temperatura
Para ambientar la habitación a una temperatura específica, oprima el
Botón de Temperatura
hasta la posición deseada. La luz debajo
de la temperatura seleccionada continuará titilando hasta que la habitación alcance la temperatura deseada.
Función de Temporizador
La Función de Temporizador puede ser activada cuando la pantalla del Calefactor se encuentre en cualquier velocidad o temperatura.
Esta función le permite a usted seleccionar la cantidad de tiempo que el Calefactor estará en funcionamiento antes de apagarse
automáticamente, de 1 hora a 7 horas. Oprimir el
Botón de Temporizador
aumentará la cantidad de tiempo, en combinaciones de
1,2 y 4 horas. Oprimir el botón continuamente resultará en que el temporizador quede fijado para un lapso de 7 horas. El Calefactor
se apagará cuando el tiempo fijado haya transcurrido. La unidad puede ser apagada oprimiendo el
Botón de Encendido.
MODELO 6405
Figura 1
Botón de
Encendido
Botón de
Temperatura
Botón de
Oscilación
Botón de
Temporizador
SAVE THESE INSTRUCTIONS
•
ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO
NOT PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR,
MULTIPLE OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE
A FIRE HAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.
•
FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG
FITS TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS
NOT OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO
NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.
• Make certain that the power source conforms to the electrical requirements of the Heater.
• Extreme caution is necessary when any Heater is used by or near children or invalids
. The Heater should not be left
operating unattended.
Never leave children unattended when the heater is on or plugged in.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended
to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. Do not attempt to defeat this safety feature.
• DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations
where flammable or explosive chemicals are stored, or in wet atmospheres.
• Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions
, or has been dropped or damaged in any
manner. To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
• Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
• Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or
damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
• Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings
may become blocked. Do not depend on the on/off
switch as the sole means of disconnecting power when servicing or moving the
heater.
Always unplug the power cord.
Read all instructions before using this Heater.
IMPORTANT SAFETY INFORMATION
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
WARNING
CAUTION
• Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so
the Heater or other objects are not resting on it. DO NOT
run Power Cord under carpeting.
DO NOT
cover Power Cord with throw rugs, runners, or
similar coverings as this may cause cord to overheat. Arrange Power Cord away from room traffic and where it will not be tripped
over.
• This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep
them at least 1 foot (0.3 m) from the sides and rear.
• This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. NEVER
locate a Heater where it may fall into a bathtub or other water container.
• DO NOT
use Heater outdoors.
• This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please
refer
to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for
Agricultural Buildings.
THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
• This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or
local codes
or standards relating to electrical requirements for Hazardous locations.
THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC
ARTICLE 500 (2008).
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the
equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the
dealer or an experienced radio/TV technician for help. The user is cautioned that changes and modifications made to the equipment without the
approval of manufacturer could void the user’s authority to operate this equipment.
Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
WARNING
