Laski P56 RX Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 59

Laski P56 RX Скачать руководство пользователя страница 43

Predátor P 56RX

43

The  grease  contained  in  the  hydraulic
track is pressurized. Never loosen grease
valve (74) for more than one turn. If the
valve  is  loosened  too  much  you  risk
expelling  grease  under  pressure  and
possible  serious  injury  to  the  machine
operator. Also never loosen grease nipple
(73).

Remove gravel or mud from between the
sprocket and the track.

Remove the screws and take off the cover
(68) to access the adjustment system.
To  loosen  the  track,  turn  the  valve  (74)
counter-clockwise but no more than one

turn. One turn of the valve (74) is sufficient for loosening the track. If grease does
not start to drain out then slowly rotate the track.

Tighten the valve (74) by turning clockwise till tight. Clean all traces of extruded
grease.
To tighten the track, connect a grease gun to grease the nipple (73) and pump grease
until the track tightens so that there is 10-15 mm of sag. Then stop it.

Front idler locking

It  is  not  normal  for  the  track  to  remain  tight  after  turning  the  valve  1
counter-clockwise  or  for  it  to  remain  loose  after  introducing  grease  into
the  grease  nipple  2.  Never  try  to  remove  the  tracks  or  disassemble  the

track-stretching cylinder since pressure of the grease inside the track is extremely
dangerous.

Removing the rubber track

-

Stop the machine on a solid and level surface. Jack up side of

machine under its main frame and support it in safe condition.
-

Remove the cover plate (68) on side of the track frame that gives

access to the adjustment system.

-

To loosen the track, slowly unscrew the valve (74) counter-clockwise for no
more than one turn. One turn of the valve (74) is sufficient for loosening the
track.

-

If grease does not start to drain out, then slowly rotate the track.

Fig. 25 – Belt tensioning

«
...
41
42
43
44
45
...
»

Содержание P56 RX




























































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды