Manual: EL-200RGB MK2
Manual: EL-200RGB MK2
page 2 / 22
page 3 / 22
English
English
1. Product and package contents
Please check if all listed parts are included and undamaged. Included in delivery:
Laser system, power cable, key, interlock bridge plug, manual, technical datasheet
2. Preliminary warning notices
1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels,
power supplies or power cords.
3. This device must not be permanently connected to mains. Disconnect it from mains or
use the power button to switch if off if not in use.
4. Never look directly into the light source of a laser projector. Danger of damage to the
eyes or even blindness in extreme circumstances!
5. Do not operate the device at high humidity or in the rain or in dusty environments.
6. Protect device against dripping or splashing water. Do not place any liquid filled
containers near to this device.
Any warranty claims are void if the warranty label is removed or tampered
with in any way.
4. Working on the device
1. This product has no user serviceable parts inside and should
only be maintained and serviced by a qualified engineer.
2. Be sure that the mains plug is not connected to the power
supply while installing the device.
3. Take off all reflecting things like rings, watches, etc.
before starting to work with or at the projector.
4. Only use non-reflecting tools to work on device.
5. Wear protective clothing (like goggles, gloves etc.) according to laser power and wave-
length of the laser.
5. Service notes
• Moisture and heat can reduce lifetime of
the laser system dramatically and expires
any warranty claim.
• Quick on/off switching of this device will
reduce durability of the laser diode dra-
matically.
• Avoid sharp knocks and shocks to this
device an endsure sufficient protection
during transportation. Look after your
Laserworld product.
• To increase durability of your laser,
protect device against overheating:
-
Always ensure sufficient ventilation.
-
Do not face spotlights (especially mo-
ving heads) to the device.
-
Check temperature after approx. 30
minutes with each new installation.
If necessary install the projector at a
place with different temperatures.
-
Keep the device dry. Protect it from
moisture, rain and damp.
-
Switch off device when it is not nee-
ded. Diodes are switched on and can
wear out even if there is no visible la-
ser output.
• Please ensure the fans and heatsinks are
clear from dust and debris otherwise the
risk of overheating may occur. If the unit
or air inlets appear to be blocked, please
contact a qualified service engineer to
maintain and service the product.
• Removal of the warranty label as well
as damages to the device caused by
improper handling, neglect of the sa-
fety instructions and service notes will
void the warranty.
3. Initial operations, safety instructions
1. Make sure to use correct voltage; see in-
formation on device & in this manual.
2. Make sure that the device is not connec-
ted to mains during installation.
3. Installation has to be done by technical
experienced and qualified persons ac-
cording to safety regulations of the res-
pective country.
4. Always ensure that maximum permissi-
ble exposure (MPE) is not exceeded in
areas accessible to the public or members
of staff.
5. In some countries an additional ins-
pection by technical control institutes
could be necessary.
6. Connect an easily accessible inter-
lock connector or circuit breaker
to the projector.
7. The power supply should be easily acces-
sible.
8. When installing the laser mount it with
a minimum distance of 15 cm from walls
and objects.
9. For safe setup e.g. on walls or ceilings
please use a safety cord. The safety cord
should be able to withstand tenfold the
weight of the device. Please follow the
accident prevention regulations of pro-
fessional associations and/or comparable
regulations for accident prevention.
10. If the device has been exposed to great
temperature changes, do not switch it
on immediately. Condensation (or any
moisture/water formed) may damage
this device.
11. Never use dimmer, RC or other electroni-
cally switched sockets. Whenever possib-
le, do not use the laser projector together
with large appliances (especially fog ma-
chines) on the same mains!
12. Ensure sufficient ventilation and do not
place the device on any warm or heat ra-
diating surface. Especially the ventilati-
on openings must not be covered!
13. Ensure that device does not get over-
heated. Make sure that the device is not
exposed to spotlights (especially moving
heads). Heat of spotlights could overheat
laser in a little while and leads to a degra-
dation of performance.
14. This unit is intended for indoor use only.
