background image

Part No. 0010-0009  Rev. A 

Copyright 
© 2006 Laserscope. All right reserved. 

Notice 
No part of this manual may be reproduced or transmitted in any form or by 
any means without the written consent of Laserscope. 
The information in this manual is subject to change without notice. 

Disclaimer 
Laserscope provides this document in its commitment to help facilitate 
consistent, positive clinical outcomes, and to reduce patient risk and injury. 
These guidelines are not, however, intended to in any way replace or 
substitute a physician’s duty of care, professional responsibility, or 
professional judgment, nor are they intended to provide any warranty, 
promise, guarantee, assumption of risk or duty, release, or indemnity. 
Physicians shall at all times maintain responsibility for patient treatment and 
outcomes, and Laserscope further assumes no liability for patient treatment 
or outcome or for physician’s negligence, breach of duty of care, or 
malpractice.  

In no way does this or any of Laserscope’s policies, procedures, training 
materials, guidelines, or instructions create an obligation for Laserscope to 
perform any services. Products and services may be purchased from 
Laserscope. 
 
Trademarks       

  

GreenLight HPS is a Laserscope trademark 
Laserscope is a registered trademark of Laserscope.  

                                      

Laserscope Corporate 
Headquarters  
3070 Orchard Drive  
San Jose, CA 95134-2011  
U.S.A.  
Tel: 800 356-7600 (Customer 
Service)  
Tel: 408 943-0636  
Fax: (+1) 408 943-1051  
www.laserscope.com 

Laserscope France, S.A.  
Parc Technologique  
18 rue du Bois Chaland  
91090 Lisses, France  
Tel: 33/1 60 86 20 49  
Fax: 33/1 60 86 14 88 

Laserscope (UK) Ltd.  
Berwyn, The Pavilions 
Llantarnam Park  
Cwmbran, South Wales,  
NP44 3UW  
United Kingdom  
Tel: 44/1633-838081  
Fax: 44/1633-838161 

 

Содержание GreenLight HPS











































































Отзывы: