manualshive.com logo in svg

Laser Technology TruPulse 200L, Руководство пользователя

Поделиться
Скачать
Laser Technology TruPulse 200L Скачать руководство пользователя страница 18

Laser Technology, Inc. TruPulse 200L User's Manual 1

st

 Edition 

Page 14 

Units of Measure 

The TruPulse 200L allows you to choose the units of measure. Distance: meters, yards or feet. 
Inclination: degrees or % Slope. To toggle the units selection: 

1.

 

From the Measurement Mode, press 

 for 4 seconds to access the System Setup Mode. 

“UnitS” will appear in the Main Display. 

2.

 

Press 

 to select the “UnitS” option. 

3.

 

Press 

 or 

 to display the previous or next distance unit option.

 

4.

 

Press 

 to select the displayed distance unit and display the inclination unit option.

 

5.

 

Press 

 or 

 to display the previous or next inclination unit option.

 

6.

 

Press 

 to select the displayed inclination unit and return to the Measurement Mode.

 

 

 

 
 

 

Each time the TruPulse 200L is powered ON, it will return to the same unit 
setting that was last used. 

Figure #10 

Содержание TruPulse 200L





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды