Laser Cut Planes HogNose Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 30

Laser Cut Planes HogNose Скачать руководство пользователя страница 18

March 19, 2018

HogNose building instructions

18

The uncovered area is required to allow for
the installation of the push rods.
This area will be covered after the receiver
and pushrods have been installed and tested.

Cover the following items.

The roof of the cockpit is best covered after
the wings have been fitted. This way the
joint can be covered and it looks neater.

If using a transparent covering film, don't
remove the film that covers the side cockpit
windows.
If using a solid colour covering, the
openings may be cut out and clear acetate
sheet attached to form the windows.

Remove all covering from along the wing
joint.

Underside of covered fuselage

Covered fuselage

Don't cover, access
required for installing
pushrods.

Don't cover
until after
wings are
fitted

No covering
along wing joint.

Cover side windows

The top surface ONLY of both wings.
The top surface ONLY of the horizontal stabiliser.
The whole of the fuselage except for the cockpit
roof and the underside of "F13".

This Photo shows the covered horizontal
stabiliser. NOTE:- This is only covered on the
upper side.

Is this photo the stabiliser has just been test
fitted and it is not glued at this stage.

Upper surface only
is covered with
film.

COVERING

«
...
16
17
18
19
20
...
»

Содержание HogNose































Отзывы:

Нет отзывов