lapara 6KR Скачать руководство пользователя страница 4

 

3

LA-ON-RACK 6K/10K 

 

1. Safety and EMC instructions

 

 
Please read carefully the following user manual and the safety instructions before installing the unit or using the 
unit! 

1.1. Transportation and Storage 

  Please transport the UPS system only in the original package to protect against shock and impact. 

  The UPS must be stored in the room where it is ventilated and dry. 

1.2. Preparation 

  Condensation may occur if the UPS system is moved directly from cold to warm environment. The 

UPS system must be absolutely dry before being installed. Please allow at least two hours for the UPS 
system to acclimate the environment.   

  Do not install the UPS system near water or in moist environments. 

  Do not install the UPS system where it would be exposed to direct sunlight or nearby heater. 

  Do not block ventilation holes in the UPS housing. 

1.3. Installation 

  Do not connect appliances or devices which would overload the UPS (e.g. big motor-type 

equipment)) to the UPS output sockets or terminal.   

  Place cables in such a way that no one can step on or trip over them.   

  Do not block air vents in the housing of UPS. The UPS must be installed in a location with good 

ventilation. Ensure enough space on each side for ventilation.   

  UPS has provided earthed terminal, in the final installed system configuration, equipotential earth 

bonding to the external UPS battery cabinets. 

  The UPS can be installed only by qualified maintenance personnel. 

  An appropriate disconnect device as short-circuit backup protection should be provided in the 

building wiring installation. 

  An integral single emergency switching device which prevents further supply to the load by the UPS 

in any mode of operation should be provided in the building wiring installation.   

  Connect the earth before connecting to the building wiring terminal.   

  Installation and Wiring must be performed in accordance with the local electrical laws and 

regulations.  

 
 

Содержание 6KR



























Отзывы: