Lantronix SCS100 страница 15 Скачать руководство пользователя

Страница: 15 / 62

SCS100/200/400 User Guide

3: The SCS200

Note:

The Reset button returns the SCS to its factory default configuration when you

press and hold it during the power-up and boot process. Resetting to factory default will
enable DHCP.

Serial Connector Pinouts

RS-232/RS-485 DB25 Connector

The DB25 connector provides a dual RS-232/RS-485 DTE serial port. The default serial
port settings are 9600 baud, 8 bits, no parity, and 1 stop bit.

DB25 Serial Connector (DTE DB25 Male)

RS-232 DB9 Connector

The SCS200 DB9 connector provides an RS-232 DTE serial port. The default serial port
settings are 9600 baud, 8 bits,

no parity, and 1 stop bit.

DB9 Serial Connector

PC Card Slot

The SCS200 PC card slot accepts Type I/II PC cards. As of this writing, the SCS200
software supports 16-bit IEEE 802.11 wireless networking PC cards, PCMCIA modem
cards, and ATA flash disks and hard-drive PC cards. New cards may be added.

Note:

Changes in firmware releases may affect compatibility.

3-2

Содержание SCS100































































Результаты поиска

Содержание SCS100

Отзывы:

Похожие инструкции для SCS100

Бренды по названию

Популярные бренды

Lantronix SCS100, Руководство пользователя

Результаты поиска

Содержание SCS100

Отзывы:

Похожие инструкции для SCS100

Бренды по названию

Популярные бренды