Lantech IES-2208CA Скачать руководство пользователя

Страница: 51 / 139

6.8.2 System Alert - Event

Having ticked the

Syslog

SMTP

checkboxes, the event log/email alert will be sent to the

system log server and the SMTP server respectively. Also, Port event log/alert (link up,

link down, and both) can be sent to the system log server/SMTP server respectively by

setting the trigger condition.



System event selection:

There are 3 event types

—Device Cold Start,

Authentication Failure, and X-ring Topology Change. The checkboxes are not

available for ticking unless the

Syslog Client Mode

on the Syslog Configuration tab

and the

E-mail Alert

on the SMTP Configuration tab are enabled first.



System Restart:

When the device executes cold start action, the system will

issue the event log/email alert to the system log/SMTP server respectively.



Power Status:

When the power consumption about PoE was unstable, he

system will issue the event log/email alert to the system log/SMTP server

Содержание IES-2208CA












































































































































Результаты поиска

Содержание IES-2208CA

Отзывы:

Похожие инструкции для IES-2208CA

Бренды по названию

Популярные бренды

Lantech IES-2208CA, Руководство пользователя

Результаты поиска

Содержание IES-2208CA

Отзывы:

Похожие инструкции для IES-2208CA

Бренды по названию

Популярные бренды