Lantech IES-2208CA страница 102 Скачать руководство пользователя

Страница: 102 / 139

Appendix A

—RJ-45 Pin Assignment

RJ-45 Pin Assignments

The UTP/STP ports will automatically sense for Fast Ethernet (10Base-T/100Base-TX

connections), or Gigabit Ethernet (10Base-T/100Base-TX/1000Base-T connections).

Auto MDI/MDIX means that the switch can connect to another switch or workstation

without changing straight through or crossover cabling. See the figures below for straight

through and crossover cable schematic.



10 /100BASE-TX Pin outs

With10/100BASE-TX cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6

for receiving data.



RJ-45 Pin Assignments

Pin Number

Assignment

Tx+

Tx-

Rx+

Rx-

[NOTE]

“+” and “-” signs represent the polarity of the wires that make up each wire pair.

The table below shows the 10/100BASE-TX MDI and MDI-X port pin outs.

Pin Number

MDI-X Signal Name

MDI Signal Name

Receive Data plus (RD+)

Transmit Data plus (TD+)

Receive Data minus (RD-)

Transmit Data minus (TD-)

Transmit Data plus (TD+)

Receive Data plus (RD+)

Transmit Data minus (TD-)

Receive Data minus (RD-)

Содержание IES-2208CA












































































































































Результаты поиска

Содержание IES-2208CA

Отзывы:

Похожие инструкции для IES-2208CA

Бренды по названию

Популярные бренды

Lantech IES-2208CA, Руководство пользователя

Результаты поиска

Содержание IES-2208CA

Отзывы:

Похожие инструкции для IES-2208CA

Бренды по названию

Популярные бренды