manualshive.com logo in svg

Lanier R/C Stinger .60 ARF, Инструкция по эксплуатации

Поделиться
Скачать
Lanier R/C Stinger .60 ARF Скачать руководство пользователя страница 9

      Lanier R/C 

Stinger .60 ARF 

 

You can connect a piece of fuel tubing(not 
supplied) from the vent tube to the muffler 
and another from the pickup line to the 
carburetor. Using foam rubber, pad the tank 
on all sides inside the fuselage. 

 

 

Cowl Mounting 
 

Trial fit the cowling in place after making 
the cut out for the engine head and muffler. 

 

  
Install the spinner back plate and align the 
cowl with it leaving 1/8" clearence between 
them. Drill a 1/8" hole in the cowl on the 
top center so the screw will go into the 
firewall. Install the 3mm screw to hold 

cowl in place. Install another screw in each 
lower corner of the firewall on both sides of 
the cowl. Using the spacer blocks on each 
side, install another screw in the cheek cowl 
area. 

 

Those 5 screws will be enough to hold the 
cowl firmly in place.  

 
Flying Wires 

 
The flying wires on the tail are functional 
and must not be left off. Locate the four 
wires with clevises, the three 2mmx20mm 
bolts and nuts, the aluminum mounting 
plate and the 2mmx8mm screw. 

 

Mount the aluminum bracket on the bottom 
of the fuselage directly in front of the tail 
wheel bracket using the 2mm x 8mm screw. 

Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 
Phone 770 532 6401 FAX. 770 532 2163 

9 

Содержание Stinger .60 ARF

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды