manualshive.com logo in svg

Lanier R/C Stinger .60 ARF, Инструкция по эксплуатации

Поделиться
Скачать
Lanier R/C Stinger .60 ARF Скачать руководство пользователя страница 1

      Lanier R/C 

Stinger .60 ARF 

   Stinger .60 ARF 
     Instructions 
                                      

 

 

 

WARNING!  THIS IS NOT A TOY! 

 

THIS IS NOT A BEGINNERS AIRPLANE 

 

This R/C kit and the model you will build from it is not a toy!  It is capable of serious bodily 
harm and property damage. It is your responsibility, and yours alone - 

to build this kit 

correctly, properly install all R/C. components and flying gear (engine, tank, radio, pushrods, etc. 
and to test the model and fly it only with experienced, competent help, using common sense and 
in accordance with all safety standards as set forth in the Academy of Model Aeronautics Safety 
Code.  It is suggested that you join the AMA and become properly insured before attempting to fly 
this model.  If you are just starting R/C modeling, consult your local hobby dealer or write to the 
Academy of Model Aeronautics to find an experienced instructor in your area.                                                                  

Write to : Academy of Model Aeronautics, 5151 Memorial Dr, Muncie, IN 47302 

 

LIMITED WARRANTY 

 

Lanier R/C is proud of the care and attention that goes into the manufacture of parts for 
its model kits.  The company warrants that for a period of 90 days, it will replace, at the 
buyers request, any parts or material shown to the company's satisfaction to have been 
defective in workmanship or material at the time of purchase. 

Lanier R/C INC. P.O. Box 458 Oakwood, GA. 30566 
Phone 770 532 6401 FAX. 770 532 2163 

1 

© Copyright 2002 Lanier R/C Inc.

Содержание Stinger .60 ARF

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды