background image

14

OPERATION CONT’D

Hints & Suggestions

Convection ovens constantly circulate air over and around the product.  This strips away the
thin layer of moisture and cool air from around the product allowing heat to penetrate more
quickly.

Cooking times can be shortened and cooking temperatures can be reduced.

To convert standard deck oven recipes, reduce the temperature 50 degrees and the time by
25%.  Make minor adjustments as necessary.

The lower the oven temperature the more even the bake.

Always weigh your product.  This will give you a more consistent size, color and quality.

Check the product near the end of the initial cooking cycle by turning on the oven light and
looking through the oven door windows.

Do not open the oven doors during baking as this will change the baking characteristics of the
oven and make it difficult to determine a final program.

If the product is overdone on the outside and underdone on the inside, reduce the baking
temperature.

If the product is pulling away from the edge of the pan, the temperature is too high or the
cooking time too long.

The convection is a mechanical piece of equipment.  The same control settings will always
give the same results.  If the results vary, problems may be because of product preparation.

Содержание ECCO-PP

























Отзывы: