LaneShark LS-3 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 43

background image

(850) 610-2870

www.lanesharkusa.com

37

Lane Shark LS-3

STORAGE

Overview

To keep your Lane Shark in its best condition, we recommend

following the storage procedures listed below. It will also make sure
your Lane Shark is o

ff

to a good start when needed. If your Lane

Shark is going to be stored for long periods of time we STRONGLY
recommend following these procedures to increase the life of your
Lane Shark.

Preparing Unit for Storage

1.  Complete maintenance checklist.
2.  Clean all mud, dirt, and debris from the Lane Shark.
3.  Tighten any loose hardware.
4.  Replace any safety/warning decals if damaged or illegible.
5.  Touch up any chipped or scratched areas.
6.  Connect hydraulic lines into each other.
7.  Store the unit in a dry area.

Removing from Storage

1.  Complete maintenance checklist.
2.  Complete safety checklist
3.  Clean all mud, dirt, and debris from the Lane Shark.
4.  Tighten any loose hardware.
5.  Replace any safety/warning decals if damaged or illegible.
6.  Touch up any chipped or scratched areas.
7.  Connect hydraulic lines into each other.
8.  Store the unit in a dry area.

Proper storage position shown below:

«
...
35
36
37
38
39
...
»

Содержание LS-3












































Отзывы:

Нет отзывов

Похожие инструкции для LS-3

Бренд: Dahle Страницы: 40

Бренд: Makita Страницы: 10

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 2

ColorCut Flatbed FB1060 Series

Бренд: Intec Страницы: 50

Personal Cutting System None

Бренд: Xyron Страницы: 24

Trav-L-Cutter E

Бренд: Wachs Страницы: 68

Бренд: Thermal Dynamics Страницы: 130

Rapter RR BC 20-42.7

Бренд: GD Страницы: 88

Бренд: Vito Agro Страницы: 64

Бренд: RASOR Страницы: 16

Бренд: Alpha tools Страницы: 104

Бренд: UnionSpecial Страницы: 18

Бренд: Masport Страницы: 7

Бренд: Stiga Страницы: 76

Бренд: Kiwi Страницы: 16

Бренд: Stow Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды