Landoll Brillion LSP5, Руководство оператора

Страница: 8 / 34

1-4 7K458-0221
TABLE OF CONTENTS
Safety Decals
Figure 1-2: Decals
528933
ITEM 5
528938
ITEM 6
528934
ITEM 11
WARNING
MOVING PART HAZARD
TO PREVENT SERIOUS INJURY FROM
MOVING PARTS:
KEEP COVERS CLOSED DURING OPERATION.
DO NOT ALLOW ANYONE TO RIDE OR CLIMB
MACHINE DURING OPERATION.
KEEP OBSERVERS AWAY.
2K123
2K123
ITEM 1
PARKING PIN
9J301
ITEM 7
9J301
ITEM 2
8J310
ITEM 3
9J302
ITEM 8
7K343
ITEM 9
4K036
ITEM 4
5D505
IMPORTANT
DISENGAGE CLUTCH (IF SO
EQUIPPED) OR RAISED SEEDER
BEFORE BACKING UP.
FAILURE TO DO SO WILL
DAMAGE BRUSH AGITATORS.
ITEM 10
7K341
ITEM 10
8K487
MACHINE MAY BE CALIBRATED FOR UNLISTED SEED AS FOLLOWS:
1. RAISE MACHINE AND LOCK IN TRANSPORT POSITION.
2. PLACE A CANVAS OR TARP ON GROUND TO CATCH SEED.
3. TURN 3/4 HEX ON SPROCKET SHAFT COUNTERCLOCKWISE(CCW)
279 REVOLUTIONS FOR 5 FOOT SEEDER
232 REVOLUTIONS FOR 6 FOOT SEEDER.
4. WEIGH SEED AND MULTIPLY BY 10 FOR 13 TOOTH DRIVER
SPROCKET AND BY 20 FOR 26 TOOTH DRIVER SPROCKET TO GET
APPROXIMATE PLANTING RATE IN POUNDS PER ACRE.
1. RATES ARE BASED UPON USING 13 TOOTH DRIVER SPROCKET. DOUBLE THESE VALUES
WHEN USING 26 TOOTH DRIVER SPROCKET.
2. RATES ARE INTENDED AS A GUIDE ONLY. VARIATIONS IN SIZE AND CLEANLINESS WILL
AFFECT RATES. CHECK ACREAGE AND POUNDS OF SEED USED FOR BEST RESULTS.
PLANTING RATES CALIBRATION
7K343 FOR LSP5 AND LSP6 SEEDERS
26 TOOTH
DRIVEN
17 TOOTH
IDLER
13 TOOTH
OR
26 TOOTH
DRIVER
13 TOOTH
3/4 HEX
CAUTION
BE SURE TO ENGAGE
PARKING PIN ON LEFT END OF
FRAME BEFORE UNHITCHING
TRACTOR. OTHERWISE
FRAME WILL TIP BACKWARDS
ABOUT FRONT AXLE
9J302
CAUTION
1. DO NOT LUBRICATE, ADJUST OR REPAIR WHEN MACHINE IS IN MOTION.
2. DO NOT TOW OR TRANSPORT FASTER THAN 15 MILES PER HOUR.
3. DO NOT RIDE OR ALLOW OTHERS TO RIDE ON THE MACHINE.
4. BLOCK UP ALL HYDRAULICALLY OR MECHANICALLY RAISED COMPONENTS TO PREVENT
UNINTENDED LOWERING OR LOWER THE MACHINE TO THE GROUND TO MAKE ADJUSTMENT
OR REPAIRS OR WHEN NOT IN USE.
5. KEEP ALL PERSONS AWAY FROM MACHINE DURING HITCHING AND OPERATING.
6. SLOW DOWN BEFORE MAKING SHARP TURNS OR USING THE BRAKE.
DRIVE SLOWLY OVER ROUGH GROUND, SIDE HILLS, AND AROUND CURVES TO AVOID TIPPING.
7. COMPLY WITH ALL LAWS WHEN TRANSPORTING THE MACHINE ON PUBLIC ROADWAYS.
8. INSTRUCT ALL OPERATORS IN THE SAFE OPERATION OF THE MACHINE.
REVIEW THE OPERATOR’S MANUAL FOR CORRECT PROCEDURES.
9. BLOCK IMPLEMENT TO PREVENT MOVEMENT WHEN UNHITCHED FROM TRACTOR.
10. KEEP ALL GUARDS AND SHIELDS IN PLACE WHILE MACHINE OR PARTS ARE IN MOTION.
8J310