background image

7K458-0221

1-3

TABLE OF CONTENTS

Safety Instructions for Towing 

Vehicles

The maximum travel speed is the lesser of
• The limit of the road conditions;
• The maximum specified ground speed;

— for towing operations as indicated in this manual 
or SIS;
— of the towed vehicle as indicated in its operator’s 
manual, SIS, or information sign;

• The maximum ground speed of the towed equipment 

combination shall be limited to the lowest specified 
ground speed of any of the towed machines. This 
speed is the ground speed limitation.

EXAMPLE: 

If the tractor is capable of 25 mph, the first 

implement has a SIS for 19 mph, and the last 
implement’s operator’s manual states its specified 
ground speed is 15 mph, the towed equipment 
combination ground speed limitation is 15 mph.

Attaching, Detaching, Storage

• Do not stand between the tractor and implement when 

attaching or detaching implement unless both are 
prevented from moving.

• Before applying pressure to the hydraulic system, be 

sure all connections are tight and that hydraulic lines 
and hoses are not damaged.

• Block implement so it will not roll when unhitched from 

the tractor.

• Relieve pressure in hydraulic lines before uncoupling 

hydraulic hoses from tractor.

NOTE

To relieve hydraulic pressure: Depending on tractor 
hydraulic system, some can be relieved by actuating 
control lever after engine is stopped. If tractor has electric 
over hydraulic controls, it may be necessary to move the 
control lever to the float position. Refer to tractor’s 
operator’s manual.
Wear protective gloves and safety glasses or goggles 
when working with hydraulic systems.

Maintenance Safety

• Block the machine so it will not roll when working on or 

under it to prevent injury in case of hydraulic failure or 
inadvertent lowering by another person.

• Do not make adjustments or lubricate machine while it 

is in motion.

• Make sure all moving parts have stopped.
• Keep all guards in place. Replace any that become 

damaged.

• Understand the procedure before doing the work. Use 

proper tools and equipment.

Protective Equipment

• Wear protective clothing and equipment appropriate 

for the job. Avoid loose fitting clothing.

• Because prolonged exposure to loud noise can cause 

hearing impairment or hearing loss, wear suitable 
hearing protection, such as earmuffs or earplugs.

Chemical Safety

Agricultural chemicals can be dangerous. Improper use 
can seriously injure persons, animals, plants, soil and 
property.
• Read chemical manufactures instructions and store or 

dispose of unused chemicals as specified. Handle 
chemicals with care and avoid inhaling smoke from 
any type of chemical fire.

• Store or dispose of unused chemicals as specified by 

the chemical manufacturer.

Prepare for Emergencies

• Keep a First Aid Kit and Fire Extinguisher handy.
• Keep emergency numbers for doctor, ambulance, 

hospital and fire department near phone.

Содержание Brillion LSP5



































Отзывы: