Landoll 6230 Скачать руководство пользователя страница 27

Страница: 27 / 80

3-5

HYDRAULIC DEPTH STOP TUBE ASSEMBLY

3-5.1

Lay the depth stop tube assembly on

top of the center frame. Insert a 5/8-11 x 3
hex head cap screw in the rear hole of the
tube assembly from the left side

(See Figure

3-5)

. Install a 5/8-11 hex nut on the screw.

Do not over tighten, as the depth stop must
pivot on this screw. Insert the screw through
the depth stop mounting plate on the center
lift and secure with a 5/8-11 hex lock nut.

3-5.2

Insert 90 deg elbow fittings in the back

and right side of the limit valve.

3-5.3

Using 5/16-18 x 4 hex head cap screws

secure the front end of the depth stop tube
assembly to the top of the frame mount with
the spacers, depth stop plate, and 5/16-18
hex lock nuts.

Attach the limit valve to the

bottom side of the center frame mount using
these same screws.

Note: It may be necessary to leave these
screws loose to attach the valve hoses later.

3-11

Содержание 6230

















































































Результаты поиска

Содержание 6230

Отзывы:

Бренды по названию

Популярные бренды

Landoll 6230, Руководство оператора

Результаты поиска

Содержание 6230

Отзывы:

Бренды по названию

Популярные бренды