background image

INTRODUCTION AND SAFETY INFORMATION

1-3

TABLE OF CONTENTS

DANGER

Transporting Safety

IMPORTANT

It is the responsibility of the owner/operator to 
comply with all state and local laws.
1.

When transporting the implement on a road or 
highway, use adequate warning symbols, reflectors, 
lights and slow moving vehicle sign as required. Slow 
moving tractors and towed implements can create a 
hazard when driven on public roads. They are 
difficult to see, especially at night.

2.

Do not tow an implement that, when fully loaded, 
weighs more than 1.5 times the weight of the towing 
vehicle.

3.

Carry reflectors or flags to mark the tractor and 
implement in case of breakdown on the road.

4.

Do not transport at speeds over 20 MPH under good 
conditions. Never travel at a speed which does not 
allow adequate control of steering and stopping. 
Reduce speed if towed load is not equipped with 
brakes.

5.

Avoid sudden stops or turns because the weight of 
the implement may cause the operator to lose control 
of the tractor. Use a tractor heavier than the 
implement.

6.

Use caution when towing behind articulated steering 
tractors; fast or sharp turns may cause the implement 
to shift sideways.

7.

Keep clear of overhead power lines and other 
obstructions when transporting. Know the transport 
height and width of your implement.

Attaching, Detaching, and 

Storage

1.

Do not stand between the tractor and implement 
when attaching or detaching implement unless both 
are not moving.

2.

Block implement so it will not roll when unhitched 
from the tractor.

3.

Store in an area where children normally do not play.

Maintenance Safety

1.

Understand the procedure before doing the work. 
Use proper tools and equipment.

2.

Make sure all moving parts have stopped.

3.

Do not make adjustments or lubricate implement 
while it is in motion.

4.

Block the implement so it will not roll when working 
on or under it to prevent injury.

High Pressure Fluid Safety

1.

Escaping fluid under pressure can be nearly invisible 
and have enough force to penetrate the skin causing 
serious injury. Use a piece of cardboard, rather than 
hands, to search for suspected leaks.

2.

Any fluid injected into the skin must be surgically 
removed within a few hours or gangrene may result.

3.

Avoid the hazard by relieving pressure before 
disconnecting hydraulic lines.

Protective Equipment

1.

Wear protective clothing and equipment.

2.

Wear clothing and equipment appropriate for the job. 
Avoid loose fitting clothing.

3.

Because prolonged exposure to loud noise can 
cause hearing impairment or hearing loss, wear 
suitable hearing protection, such as earmuffs or 
earplugs.

Chemical Safety

1.

Agricultural chemicals can be dangerous. Improper 
use can seriously injure persons, animals, plants, soil 
and property.

2.

Read chemical manufactures instructions and store 
or dispose of unused chemicals as specified. 

3.

Handle chemicals with care and avoid inhaling 
smoke from any type of chemical fire.

4.

Store or dispose of unused chemicals as specified by 
the chemical manufacturer.

Prepare for Emergencies

1.

Keep a First Aid Kit and Fire Extinguisher handy.

2.

Keep emergency numbers for doctor, ambulance, 
hospital and fire department near the phone.

• Do not allow anyone to ride on the tractor or 
implement. Riders could be struck by foreign 
objects or thrown from the implement.
• Never allow children to operate equipment.
• Keep bystanders away from implement during 
operation.

Содержание 2512 Series











































Отзывы: