OPERATION AND MAINTENANCE
4-7
Field Operation - 3-PT Hitch Type
1. Lower the In-Row Ripper to the ground and pull it a
few feet at the approximate desired depth.
2. Check for front-to-rear levelness. Level the frame by
adjusting the three-point hitch top arm until the frame
is level relative to the ground.
3. Set the depth by adjusting the gauge wheels. For
stability, it is important that the gauge wheels are
always in contact with the soil. Adjust the gauge
wheels as follows:
a. Loosen the keeper nut on the adjustable top link.
b. Shorten the top link to shallow up the ripper,
lengthen the link to allow the ripper to run deeper.
c. Snug up the top link keeper nut.
4. Always lift the In-Row Ripper completely out of the
ground before turning or backing to prevent shank or
coulter damage or damage to their respective
mounting brackets.
5. Reduce speed at field ends, raise the In-Row Ripper
out of the ground, and assist turning by using the
wheel brakes, if necessary.
6. After a few hours of initial operation, check all cap
screws for tightness. Tighten any loose cap screws.
7. Coulters should be adjusted to operate only deep
enough to be in firm soil and cut the residue.
Generally, the harder the soil, the less pressure
should be used on the coulters. Adjust the single
coulters by loosening the coulter mount U-bolts,
sliding the coulter up or down as needed. Re-tighten
the coulter mount making sure the coulter standard
tube is square with the ripper frame.
Wheel Bearing Maintenance
1. Check wheel bearings and coulter bearings
occasionally for excessive end play. To correctly
replace the wheel bearings:
2. Place the frame on blocks or stands sufficient to lift
the tire clear of the ground.
3. Remove the hub cap, cotter pin, slotted nut, and
washer.
4. Remove the hub. Clean and inspect the bearings and
hub cavity. Replace any worn or defective parts.
5. Repack the bearings using a high-quality wheel
bearing grease.
6. Replace the hub with a new seal and inner bearing in
place.
7. Install the outer bearing cone, washer, and slotted nut.
8. Tighten the slotted nut while rotating the hub until
there is a slight resistance to wheel rotation. Back the
slotted nut off one notch until the wheel rotates freely
without end play.
9. Install a new cotter pin and the hub cap.
10. Wheel bearing maintenance should be performed at
the beginning of every season of use.
Coulter Spring Adjustment
No spring adjustment is necessary on the coulters. All
adjustments were made before shipping at the factory.
Initial operating force to move coulter upwards is 540
pounds. The preload has proved to be more than
adequate for most conditions.
IMPORTANT
The coulters should NOT be run more than 2-3" deep.
CAUTION
Lubrication
When lubricating the machine, SAE multi-purpose EP
grease, or EP grease with 3-5% molybdenum sulfide is
recommended. Wipe soil from fittings before greasing.
Replace any lost or broken fittings immediately.
•
Grease Coulter Hub and Swivel Mount Casting after
20 hours of use.
•
Grease Wheel Hubs after 50 hours of use.
•
Grease Wing Frame Fold (2 ea.) after 10 hours of use.
•
Grease Finishing Options (ie. Closer Wheel, Flat Bar
Basket, Closer Disc, Crumbler Reel, Packer Reel,
Treader) after 10 hours of use.
Storage
The service life of the In-Row Ripper will be extended by
proper off-season storage practices. Before storing,
complete the following procedures:
1. Completely clean the unit.
2. Inspect the machine for worn or defective parts.
Replace parts as needed to avoid delays the
following season.
3. Repaint all areas where the original paint film is worn
off.
4. Grease all exposed metal surfaces of shanks, points,
and coulters.
5. Lubricate as suggested in
6. Store the unit in a shed or under a tarpaulin to protect
it from the weather. The ground tools and tires
should rest on a board or other device to keep them
out of the soil.
Any attempt to make coulter force greater than
factory setting may contribute to premature failure
of parts and warranty shall be null and void.
Содержание 2511 IN-3-30 2511 N-4-30 2511 N-5-30
