Landis S755 (G2) Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 28

background image

Operator Manual S755 (G2) / S755 XL (G2)

October 2017

Landis International - 7

Power Switch

Emergency Button

START-UP

•

EYE PROTECTION SHOULD ALWAYS BE WORN BY THE OPERATOR AND OTHERS IN THE WORK AREA WHEN
SETTING UP THE MACHINE. EYE PROTECTION IS REQUIRED FOR PROTECTION FROM FLYING DEBRIS AND
DUST, WHICH COULD CAUSE EYE INJURY.

Before shipment, your Landis Finisher S755

(G2)

/ S755 XL

(G2)

was checked at the

factory for proper adjustment and operation. However, due to the possibility of
jarring or damage during handling and shipping, it is necessary to check that the
machine is in proper working order before use.

•

BEFORE INITIAL START UP, TURN SANDING BELTS BY HAND TO ENSURE THAT ALL PARTS ARE FREE. DO NOT
START FINISHER BEFORE CHECKING FOR PROPER SANDING BELT TRACKING.

BEFORE CONNECTION TO AN ELECTRICAL POWER SUPPLY

1.

Check that the main switch is off.

2.

Rotate the sanding belts to see that all parts are free and not

binding.  Continue for one complete rotation of the sanding belt,
checking both belts for tears or other damage.  You can tell that
one complete revolution has been made when the joint of the
sanding belt has gone by the front pulley twice.

3.

Rotate the trimmer section by moving the sole trimmer guard

and turning the feather edge back guard by hand. Make sure
the guards according to the position of the knife. Manual
adjustment procedure page 11.

Trimmer

Brushes

Sanding

Belt

Blower

«
...
5
6
7
8
9
...
»

Содержание S755 (G2)





























Отзывы:

Нет отзывов

Похожие инструкции для S755 (G2)

Бренд: Minuteman Страницы: 28

Orbit 20 Pro Plus

Бренд: Minuteman Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды