background image

LANDA PGDC  •  8.916-596.0  •    REV. 5/13

3

 

 

PRESSURE W

ASHER

  

OPERA

TOR’S MANU

AL

  

INTRODUCTION & ImpORTaNT SafeTy INfORmaTION

Thank you for purchasing this Pressure Washer.
We reserve the right to make changes at any time 
without incurring any obligation.

Owner/User Responsibility:

The owner and/or user must have an understanding of 
the manufacturer’s operating instructions and warnings 
before using this pressure washer. Warning information 
should be emphasized and understood. If the operator 
is not fluent in English, the manufacturer’s instructions 
and warnings shall be read to and discussed with 
the operator in the operator’s native language by the 
purchaser/owner, making sure that the operator com-
prehends its contents.
Owner and/or user must study and maintain for future 
reference the manufacturers’ instructions.
The operator must know how to stop the machine 
quickly and understand the operation of all controls. 
Never permit anyone to operate the engine without 
proper instructions.

SaVe THeSe INSTRUCTIONS

This manual should be considered a permanent 
part of the machine and should remain with it if 
machine is resold.
When ordering parts, please specify model and 
serial number. Use only identical replacement parts.
This machine is to be used only by trained operators.

ImpORTaNT SafeTy 

INfORmaTION

ReaD OpeRaTOR’S 

maNUal THOROUgHly 

pRIOR TO USe.

WARNING: To reduce the risk of 

injury, read operating instruc-
tions carefully before using.

  1.  Read the owner's manual 

thoroughly. Failure to fol-
low instructions could cause 
malfunction of the machine 
and result in death, serious 
bodily injury and/or property  
damage.

  2.  Know how to stop the machine and bleed pressure 

quickly. Be thoroughly familiar with the controls.

  3.  Stay alert — watch what you are doing.
 

WARNING

keep WaTeR 

SpRay aWay fROm 

eleCTRICal WIRINg.

WARNING: Keep wand, hose, and 

water spray away from electric 
wiring or fatal electric shock may 
result.

4.    All installations must comply 

with local codes. Contact 
your electrician, plumber, 
utility company or the selling 
distributor for specific details.

WARNING

eaR pROTeCTION 

mUST be WORN

WARNING: This machine exceeds 

85 db appropriate ear protection 
must be worn.

WARNING

USe pROTeCTIVe  

eye WeaR 

aND ClOTHINg  

WHeN OpeRaTINg 

THIS eqUIpmeNT.

WARNING: High pressure spray 

can cause paint chips or other 
particles to become airborne 
and fly at high speeds. To avoid 
personal injury, eye, hand and 
foot safety devices must be 
worn.

  5.   Eye, hand, and foot protection 

must be worn when using this 
equipment.

  6.  Keep operating area clear of all persons.
 

RISk Of explOSION: 

OpeRaTe ONly WHeRe 

OpeN flame OR TORCH 

IS peRmITTeD

WARNING

WARNING: Flammable liquids 

can create fumes which can ig-
nite, causing property damage 
or severe injury.
WARNING: Risk of explosion — 
Operate only where open flame 
or torch is permitted.

 

RISk Of fIRe.  

DO NOT aDD fUel 

WHeN OpeRaTINg 

maCHINe.

WARNING

WARNING: Risk of fire — Do not 

add fuel when the product is 
operating or still hot. 
WARNING: Do not use gasoline 
crankcase draining or oil con-
taining gasoline, solvents or 
alcohol. Doing so will result in 
fire and/or explosion.
WARNING: Risk of fire — Do not 

Spray flammable liquids. 

  7.  Allow engine to cool for 1-2 minutes before refuel-

ing. If any fuel is spilled, make sure the area is dry 
before testing the spark plug or starting the engine. 
(Fire and/or explosion may occur if this is not done.)

    Gasoline engines on mobile or portable equipment 

shall be refueled:

   a.  outdoors;
    b.  with the engine on the equipment stopped;
   c.  with no source of ignition within 10 feet of  

 

the dispensing point; and

    d.  with an allowance made for expansion of the  

 

fuel should the equipment be exposed to a  

 

higher ambient temperature.

Содержание Pgdc4-3500







































Отзывы: