![background image](http://html1.mh-extra.com/html/samsung/wf219anw-xaa/wf219anw-xaa_fast-track-troubleshooting_4768354001.webp)
Fast Track Troubleshooting
Models:
WF219ANW/XAA
WF219ANB/XAA
Publication # tsWF219 Revision Date 1/15/2010
Quick Test Mode
Note: This test erases all faults and memory
:
To enter press Spin,
Soil, & Power
simultaneously with the power off.
1. All LED’s light up and the washer beeps as it
enters the Quick Test Mode.
2. The unit displays the software then clears the
EEprom.
3. After the displaying the software version, Jog
dial CCW to display “F4”
If EEEE is displayed the PCB ass’y is defective.
4. When the model version (F4) is displayed. Press
the following keys to test the various components
Press
Temp Key
to cycle through the Water Valves
circuit test in this order: Cold Main, Bleach, Cold Main
& Bleach for Fabric Softener, Hot, then off.
Press
Spin Key
to test the motor
Press
Soil Level
to test Door Lock/Unlock circuit.
Press
Signal Key
to test the Pump
Service Mode:
This mode allows more detailed operation tests and trouble-
shooting, to enter press
Signal & Extra Rinse
simultaneously with the power on.
While in Service Mode the following tests can be performed:
Quick Spin Test =
Delay Start & Spin: This
accelerates
the drum motor from 0 to maximum RPM over a few min-
utes.
Note: Stay with the washer during this test, out of bal-
ance detection is bypassed and the door may not lock.
Press the Start/Pause button during the test to hold its spinning
speed for 10 minutes before going back to Quick Spin Test
Mode.
Cycle Count =
Press the Signal button to see how many times
the unit was used
Soft Ware # =
Press the Soil button to see the software version
information
Fast Time Down =
Press the Temp button to advance to the
next cycle
Fault Code Test =
Press the Spin button to view the stored fault
codes – then turn Dial to view error codes (Push Start/Pause
while the code is displayed to view the number of cycles since
the error occurred)
Peripheral (Main PCB) input Tests
1.
Select Extra Wash. Then turn the Dial
so that the
Normal
is
turned on. Next, press the Start/Pause Key. The Water
Temperature will be displayed in Fahrenheit.
2.
Select Extra Wash. Then turn the Dial
so that the
White
is
turned on. Next, press the Start/Pause Key. The door status will
be displayed (OP if open, CL if closed).
3.
Select Extra Wash. Then turn the Dial
so that the
Wool
is
turned on. Next, press the Start/Pause Key. The door lock
Switch status will be displayed (UL if unlocked, Lo if locked).
4.
Select Extra Wash. Then turn the Dial
so that the
Perm Press
is turned on. Next, press the Start/Pause Key. The Water
Frequency will be displayed.
IMPORTANT SAFETY NOTICE
–
“For Technicians Only”
This service data sheet is
intended for use by persons having electrical, electronic, and mechanical experience
and knowledge at a level generally considered acceptable in the appliance repair trade.
Any attempt to repair a major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible, nor assume any liability for
injury or damage of any kind arising from the use of this data sheet.
Location considerations
Do not install your washer in areas where
water may freeze, since your washer will
always maintain some water in its water
valve, pump, and hose areas. This can cause
damage the belts, the pump, hoses and other
components.
Operating temperature should
be above 60°F/16°C.
1
Summary of Contents for WF219ANW/XAA
Page 2: ...WF219 2...