Land Pride RCP2660, Руководство оператора

Страница: 49 / 74

Section 5: Optional Equipment
Table of Contents
11/2/18 RCP2660, RCPM2660, RCP3060 & RCPM3060: Parallel Arm Rotary Cutter: 316-111M:
45
Tractor Axle Housing
Figure 5-5
Attach Upper Axle Mounts
Refer to Figure 5-4 on page 44 & Figure 5-5:
1. Place axle mount (#6) on top of the left-hand axle
housing with notch "A" in mount (#6) aligned with
boss "A" on the axle housing and bolts (#8A & #8B)
in notches (#8A & #8B) in the axle housing.
2. Clamp axle mount (#6) to the axle housing with four
5/8"-11 x 8" GR5 bolts (#8), lower axle mounting
plate (#7), flat washers (#4), and lock nuts (#5).
3. Tighten lock nuts to the correct torque.
4. Repeat steps 1-3 to attach remaining axle
mount (#6) on the right-hand side of the tractor.
5. Attach non jam nut end of turnbuckle (#9A) to axle
mount (#6) on the left-hand side with bent pin (#10).
Secure bent pin with hairpin cotter (#11).
6. Repeat step 5 to attach turnbuckle (#9B) to axle
mount (#6) on the right-hand side.
7. Support turnbuckles (#9A & #9B) up with bungee
cords, rope or other means to hook-up the cutter to
the tractor’s 3-point arms.
8. Remove existing customer supplied hairpin
cotter (#21) and Cat. lll hitch pin (#20).
9. Insert Cat. lll to Cat. ll adapters (#13) in the top center
Cat. lll hitch pin holes with flanges on the inside as
shown.
10. Install a new Cat. ll hitch pin (#20) and secure with a
new hitch pin keeper. Customer to supply hitch pin
and hitch pin keeper.
A
Tractor Axle Housing
39791
8B 8A
NOTE: Jam nuts (#12) on turnbuckles (#9A & #9B)
are easier to access if that end of the turnbuckles
are attached to lower mounts (#1) as shown.
Attach Stabilizer Turnbuckles
Refer to Figure 5-4 on page 44:
1. Attach Parallel Arm Cutter to the tractor and install
the driveline. Refer to
“Hook-up Rotary Cutter” on
page 14 for detailed instructions.
2. Make certain the cutter deck has been leveled before
installing the turnbuckles. Refer to “Deck Level
Adjustments” on page 33
3. Raise 3-point arms with the tractor control lever until
driveline is horizontal.
4. Shut tractor down properly without changing the
height of the tractor’s lower 3-point arms. Refer to
“Tractor Shutdown Procedure” on page 37.
5. Place jacks under the cutter’s 3-point mainframe and
adjust jacks up until against the mainframe to keep
the 3-point lift system from falling while installing
turnbuckles (#9A & #9B).
6. Loosen jam nut (#12) and adjust turnbuckle (#9A)
until lower holes in turnbuckle clevis align with hole in
lower left-hand link mount (#1). Do not tighten jam
nut at this time.
7. Attach jam nut end (#12) of turnbuckle (#9A) to the
lower left-hand link mount (#1) with bent pin (#10).
Secure bent pin with hairpin cotter (#11).
8. Repeat steps 6 & 7 to attach turnbuckle (#9B) to
right-hand lower link mount (#2).
9. Tighten right-hand stabilizer turnbuckle (#9B) until
you can not tighten it any more.
10. Loosen left-hand stabilizer turnbuckle (#9A) as much
as possible.
11. Tighten 1 1/2"-6 jam nuts (#12) against
turnbuckles (#9A & #9B).
NOTE: The Kubota tractor must be hooked-up the
Parallel Arm Cutter, driveline installed, and cutter
deck leveled before stabilizer turnbuckles can be
installed. Once the turnbuckles are installed, the
3-point lower arms and upper center link can not be
adjusted to level the cutter.