Land Pride RCM4715 Скачать руководство пользователя страница 23

Страница: 23 / 72

Section 1: Assembly & Set-up

RC(M)4715 & RCG(M)4715 Rotary Cutters 334-113M

6/3/20

Table of Contents

Restart tractor and back up to cutter hitch until hitch

bushing (#10) aligns with holes in swivel clevis (#9).

8. Shut tractor down properly before dismounting.
9. Insert 1" x 6 1/2" GR5 hex bolt (#2) through swivel

clevis (#9) and hitch bushing (#10). Secure bolt with

locknut (#1). Tighten locknut snug to remove all play.

Do not torque 1" locknut at this time.

10. Lower park jack (#3) until hitch weight is supported

by the drawbar.

11. Relocate park jack (#3) from hitch frame to

left-hand wing storage base with detent pin (#8).

Ensure jack base is level with, or lower than the jack

crank head, especially after the wings are folded up.

See cover picture for correct positioning

12. Attach hitch safety chain (#4) to tractor. Adjust length

to remove slack except what is necessary to permit

turning. Securely lock chain hook to the safety chain.

13. Continue with

“Hydraulic Hook-up”

below.

Hydraulic Hook-up

The required number of duplex outlets on the tractor is

dependent upon how the cutter is set-up. The standard

cutter is equipped with three hydraulic cylinders with one

in the center for lifting the cutter and one on each wing for

folding the wings simultaneously. The center lift cylinder

is set up for single-action (one way) operation. The wings

can be set up with single-action (one way) or dual-action

(both way) operation.
Each duplex outlet on your tractor can perform just one

operation. One outlet is needed for lifting the cutter and

one for folding the wings simultaneously. Two outlets are

needed to fold the wings independently. It is highly

recommended to connect the wing fold hose(s) to a

duplex outlet with float capabilities and use the float

when in field operation.
The black handled hose is for the lift cylinder. The red

handled hose is for simultaneous fold or right hand wing

fold when setup independently. The yellow handled hose

is for left hand wing fold when set up independently.

When set up for dual-action fold, the handles have

directional arrows to identify what the hose does when

charged. See

“Figure 1-14”

WARNING

To prevent serious injury or death:
Hydraulic fluid under high pressure can penetrate the skin

and/or eyes causing a serious injury. Wear protective gloves

and safety glasses or goggles when working with hydraulic

systems. Use a piece of cardboard or wood rather than hands

when searching for leaks. A doctor familiar with this type of

injury must treat the injury within a few hours or gangrene

may result. DO NOT DELAY.

IMPORTANT:

Before moving the cutter, relocate

park jack by storing it on the left wing deck. Make

sure the jack is stored with its base level or lower

than the head to prevent water and freeze damage.

Hydraulic Hook-up (LP Performance Hitch Shown)

Figure 1-13

Refer to Figure 1-13:

1. Route hydraulic hoses (#7) through hose support

loop (#14) and attach couplers to the tractor remote

outlets. If tractor has a float option on one of the

outlets, connect wing lift hose to that outlet and set

tractor control lever for that outlet in float position

before cutting.

2. Apply spiraled hose wrap (#12) to hydraulic hoses

(#7) as needed to keep the hoses from pinch areas

caused by raising and lowering the deck, folding the

wing up and down, and while making turns with the

tractor.

Hydraulic Hose Hand Grips

Figure 1-14

72220

Hand Grips with Cylinder Extension Symbol

Hand Grips with Cylinder Retraction Symbol

35553

Handle Color

Operation

Black Handle:

Engages lift cylinder to raise

Red Handle:

Simultaneous fold/Right wing fold

Yellow Handle:

Left wing fold

Содержание RCM4715









































































Результаты поиска

Содержание RCM4715

Отзывы:

Похожие инструкции для RCM4715

Бренды по названию

Популярные бренды

Land Pride RCM4715, Руководство оператора

Результаты поиска

Содержание RCM4715

Отзывы:

Похожие инструкции для RCM4715

Бренды по названию

Популярные бренды