Land Pride RCM3712 Скачать руководство пользователя

Страница: 25 / 64

Section 1: Assembly & Set-up

RC(M)3712 & RCG(M)3712 Rotary Cutters 334-203M

11/6/18

Driveline Hanger Adjustment

Move tractor control lever to extend hydraulic lift
cylinder (#1) until pressure against stroke control
spacers (#2) is removed.

2. Without relieving hydraulic pressure, Shut tractor

down properly before dismounting. Refer to

“Tractor

Shutdown Procedure”

on page 13.

WARNING

To avoid serious injury or death: Stay clear from underneath

the cutter and directly behind transport tires. The cutter could

fall suddenly causing the decks to lower and tires to roll back.

3. Remove all stroke control spacers (#2) from center

hydraulic lift cylinder (#1) by spreading them apart at
the break line.

4. Start tractor and lower cutter until front skids are

resting on the ground or on support blocks.

5. Shut tractor down properly before dismounting.

6. Replace stroke control spacers (#2) as needed to

support wheels at this position.

Refer to Figure 1-22:

With driveline attached to tractor, rotate driveline
hanger (#1) up as shown.

8. Loosen nuts securing carriage bolts (#3) and adjust

driveline hanger (#1) up until there is a small gap
between driveline (#5) and hanger (#1).

9. If driveline hanger (#1) is adjusted fully up and needs

to adjust higher, remove carriage bolts (#3) and
reattach hanger to the upper two square holes (#2)
with existing flat washers, lock washers, hex nuts,
and carriage bolts (#3). Continue to adjust hanger to
underside of driveline.

10. Draw nuts securing carriage bolts (#3) up snug and

rotate driveline hanger (#1) down. If hanger makes
contact with driveline (#5), readjust hanger down
until it misses the driveline.

11. Tighten 3/8"-16 GR5 bolts (#3) to the correct torque.

12. Rotate driveline hanger (#1) down.

IMPORTANT:

Always rotate driveline hanger down

before moving cutter to prevent damage to driveline.

Hydraulic Lift Cylinder and Stroke Control Spacers

Figure 1-21

Driveline Hanger Adjustment

Figure 1-22

70468

70467

Содержание RCM3712

































































Результаты поиска

Содержание RCM3712

Отзывы:

Похожие инструкции для RCM3712

Бренды по названию

Популярные бренды

Land Pride RCM3712, Руководство оператора

Результаты поиска

Содержание RCM3712

Отзывы:

Похожие инструкции для RCM3712

Бренды по названию

Популярные бренды