Land Pride RCG3715 Скачать руководство пользователя

Страница: 57 / 66

Section 5: Maintenance & Lubrication

RC(M)3715 & RCG(M)3715 Rotary Cutters 334-114M

1/26/21

Table of Contents

Figure 5-14

33994

8-10 pumps

Zerk Located through slot in tube

CV Driveline without overrunning clutch

23556

8-10 pumps

CV Driveline with overrunning clutch

39280

4-5 pumps

2-3 pumps

4-6 pumps

CV Driveline without overrunning clutch

23556

CV Driveline with overrunning clutch

39280

4-5 pumps

2-3 pumps

4-6 pumps

2-3 pumps

CV Main Driveline Profile Tubes
With External Grease Point

CV = Constant Velocity

Type of Lubrication: Multi-purpose Grease

Quantity = 8-10 pumps

CV Main Driveline Joints

Type of Lubrication: Multi-purpose Grease
For instructions on how to access grease zerks shown

Figure 5-14:

See

“Accessing CV Driveline Joints”

on page 54.

•

The constant velocity joint should be greased in a

straight position forcing grease through the passages

and into the cavity. After lubrication, grease should

be visible around the ball joints.

•

Grease fittings located on the u

joints, driveline

shields and overrunning clutch should be lubricated

every 8 Hrs of operation.

IMPORTANT:

To extend the life of the constant

velocity joint, extensive lubrication must be

performed every 8 hours of operation.

Hours

CV Main Driveline Shield Grease Point

Type of Lubrication: Multi-purpose Grease
Quantity = 2-3 Pumps

Hours

Содержание RCG3715



































































Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды

Land Pride RCG3715, Руководство оператора

Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды