Land Pride RC5014 Скачать руководство пользователя

Страница: 5 / 44

Important Safety Information

2/02/08

RC5014 (540 RPM) and RCM5014 (1000 RPM) Rotary Cutters 330-117M

Land Pride

Table of Contents

Prepare for Emergencies

▲

Be prepared if a fire starts.

▲

Keep a first aid kit and fire

extinguisher handy.

▲

Keep emergency numbers for

doctor, ambulance, hospital and
fire department near phone.

911

Wear
Protective Equipment

▲

Protective clothing and equipment

should be worn.

▲

Wear clothing and equipment

appropriate for the job. Avoid
loose fitting clothing.

▲

Prolonged exposure to loud noise

can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.

▲

Operating equipment safely

requires the full attention of the
operator. Avoid wearing radio
headphones while operating
machinery.

These are common practices that may or may not be applicable to the products described in
this manual.

Keep Riders
Off Machinery

▲

Riders obstruct the operator’s

view. Riders could be struck by
foreign objects or thrown from the
machine.

▲

Never allow children to operate

equipment.

Tire Safety

▲

Tire changing can be dangerous

and should be preformed by
trained personnel using the
correct tools and equipment.

▲

When inflating tires, use a clip-on

chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.

▲

When removing and installing

wheels, use wheel handling
equipment adequate for the
weight involved.

Avoid High
Pressure Fluids Hazard

▲

Escaping fluid under pressure can

penetrate the skin causing serious
injury.

▲

Avoid the hazard by relieving

pressure before disconnecting
hydraulic lines or performing work
on the system.

▲

Make sure all hydraulic fluid

connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.

▲

Use a piece of paper or

cardboard, NOT BODY PARTS, to
check for suspected leaks.

▲

Wear protective gloves and safety

glasses or goggles when working
with hydraulic systems.

▲

If an accident occurs, see a
doctor immediately. Any fluid
injected into the skin must be
treated within a few hours or
gangrene may result.

Содержание RC5014













































Результаты поиска

Содержание RC5014

Отзывы:

Похожие инструкции для RC5014

Бренды по названию

Популярные бренды

Land Pride RC5014, Руководство оператора

Результаты поиска

Содержание RC5014

Отзывы:

Похожие инструкции для RC5014

Бренды по названию

Популярные бренды