Land Pride RC5014 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 44

background image

Table of Contents

Land Pride

Table of Contents

RC5014 (540 RPM) and RCM5014 (1000 RPM) Rotary Cutters 330-117M

2/02/08

©

Copyright 2009 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land
Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves
the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Important Safety Information . . . . . . . . . . .1

Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . .10

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . 10

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . 10

Serial Number Plate . . . . . . . . . . . . . . . . . . . . 10
Free Maintenance Video . . . . . . . . . . . . . . . . . 10
Further Assistance . . . . . . . . . . . . . . . . . . . . . 10

Section 1: Assembly and Set-up . . . . . . .11

Tractor Requirements . . . . . . . . . . . . . . . . . . . . . 11

Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hydraulic Outlets . . . . . . . . . . . . . . . . . . . . . . . 11
PTO Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Before You Start  . . . . . . . . . . . . . . . . . . . . . . . . . 11
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . 11
Hitch Types  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Standard Clevis Hitch . . . . . . . . . . . . . . . . . . . 12
Pintle Hitch (Optional) . . . . . . . . . . . . . . . . . . . 12

Hitch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wing Axle Assembly . . . . . . . . . . . . . . . . . . . . . . 12
Tractor Hook-up . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Driveline Installation . . . . . . . . . . . . . . . . . . . . . . . 13

Check Driveline Length . . . . . . . . . . . . . . . . . . 14

Hydraulic Hook-up . . . . . . . . . . . . . . . . . . . . . . . . 14
Unhooking From the Cutter . . . . . . . . . . . . . . . . . 15

Section 2: Adjustments . . . . . . . . . . . . . .16

Center and Wing Section Leveling . . . . . . . . . . . . 16
Cutting Height Adjustment . . . . . . . . . . . . . . . . . . 16

Section 3: Operating Instructions . . . . . .17

Pre-Start Checklist . . . . . . . . . . . . . . . . . . . . . . . . 17
Inspection Procedures . . . . . . . . . . . . . . . . . . . . . 17
Transport Locks . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Transporting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Field Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Operating Speed  . . . . . . . . . . . . . . . . . . . . . . . . . 19
Wing Operating Angle  . . . . . . . . . . . . . . . . . . . . . 19
Driveline Turning Angle . . . . . . . . . . . . . . . . . . . . 20
General Operating Instructions  . . . . . . . . . . . . . . 20

Section 4: Options . . . . . . . . . . . . . . . . . .22

Safety Guard Options . . . . . . . . . . . . . . . . . . . . . . 22
Wheel Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Driveline Options . . . . . . . . . . . . . . . . . . . . . . . . . 22
Hydraulic Accessories . . . . . . . . . . . . . . . . . . . . . 23
Hitch Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Section 5: Maintenance & Lubrication . .24

General Maintenance Information  . . . . . . . . . . . . 24
Tractor Maintenance  . . . . . . . . . . . . . . . . . . . . . . 24
Cutter Blade Maintenance  . . . . . . . . . . . . . . . . . . 24
Drivelines With Slip Clutches . . . . . . . . . . . . . . . . 25

Type A Clutches . . . . . . . . . . . . . . . . . . . . . . . 26
Type B Clutches . . . . . . . . . . . . . . . . . . . . . . . 27

Skid Shoe Maintenance . . . . . . . . . . . . . . . . . . . . 28

Center Skid Shoe . . . . . . . . . . . . . . . . . . . . . . 28
Wing Skid Shoe . . . . . . . . . . . . . . . . . . . . . . . . 29
Weight Box Skid Shoe . . . . . . . . . . . . . . . . . . . 29

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . 30

Axle Hub Bearing  . . . . . . . . . . . . . . . . . . . . . . 30
Adjustable Turnbuckle . . . . . . . . . . . . . . . . . . . 30
Main Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Divider Box  . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Intermediate Driveline Joints . . . . . . . . . . . . . . 32
Conventional Driveline Profile Tubes . . . . . . . . 32
Conventional Driveline Joints & Shields  . . . . . 32
Constant Velocity Driveline Profile Tubes  . . . . 33
Constant Velocity Driveline

Joints & Shields . . . . . . . . . . . . . . . . . . . . . . . . 33
Wing Driveline Profile Tubes . . . . . . . . . . . . . . 34
Wing Driveline Joints & Shields . . . . . . . . . . . . 34

Section 6: Specifications& Capacities . .35

Section 7: Features and Benefits . . . . . .37

Section 8: Troubleshooting . . . . . . . . . . .39

Section 9: Appendix . . . . . . . . . . . . . . . . .40

Torque Values Chart . . . . . . . . . . . . . . . . . . . . . . 40
Tire Inflation Chart . . . . . . . . . . . . . . . . . . . . . . . . 40
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

«
1
2
3
4
...
»

Содержание RC5014













































Отзывы:

Нет отзывов

Похожие инструкции для RC5014

Бренд: IDEAL Страницы: 37

Бренд: Daewoo Страницы: 33

Бренд: Maktec Страницы: 8

Бренд: Rockwell Страницы: 20

Бренд: NUTOOL Страницы: 67

HT-2556 D, HT-2576 E

Бренд: Dolmar Страницы: 88

Бренд: Poulan Pro Страницы: 38

Бренд: Kyocera Страницы: 88

Бренд: Ryobi Страницы: 10

Бренд: Signode Страницы: 2

Бренд: Stihl Страницы: 40

Бренд: Baileigh Страницы: 40

Бренд: Zenoah Страницы: 17

Бренд: Tanaka Страницы: 21

Бренд: Gartenmeister Страницы: 56

Бренд: Partner Страницы: 18

Бренд: Hard Head Страницы: 9

Бренд: Omax Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды