Land Pride NTS2607 Скачать руководство пользователя

Страница: 65 / 78

Section 8: Maintenance & Lubrication

NTS2607, NTS2609, & NTS2611 No-Till Seeder 329-141M

Table of Contents

9/10/20

1. Park tractor and seeder on flat level ground, slow

engine to an idle, and place gear selector in park or

set park brake.

2. With tractor control lever, raise seeder high enough

to place support blocks (#4) under both ends of the

rear packer roller. See “

Important

” note above.

3. Shut tractor engine off and remove switch key before

dismounting tractor.

4. Place a solid support block (#4) under the right-hand

skid shoe as shown and a second support block (#4)

under the far left-hand bearing support (not shown).

Reference NTS2609 and NTS2611 seeders only:

Place a 1 1/2" wide solid support block (#5) under the

middle bearing support.

6. Restart tractor and lower seeder until the rear roller

assembly is resting on the support blocks.

Shut tractor engine off and remove its switch key.

8. Check spiked roller clamps (#2) and rear roller

wheels (#3) to ensure they all rotate freely. If they do

not rotate freely, repeat steps 2-8.

9. Loosen 3/8"-16 hex nuts (#2) on all plain rear roller

clamps (#6) and all spike roller clamps (#1A, #1B,

#1C, & #1D). Note, clamp (#1D) is not included with

NTS2609 shown in Figure 8-5.

IMPORTANT:

Use only support blocks that are

made of solid hard wood or steel. Do not use

concrete blocks. Support blocks must support the

spikes off the ground and must not interfere with rear

roller wheel and spike rotation.

IMPORTANT:

Adjust spiked roller clamp bolts 60

clockwise from the previously tightened clamp to

ensure continuous spike engaged with the ground.

10. Adjust rear rollers (#3) as follows. Do not exceed

notched clearances in the rear scraper bars (#7).

NTS2607

a. Slide all rear roller wheels (#3) and spiked roller

clamps (#6) towards the center of the rear packer

roller assembly until all slack is removed.

b. Continue with step 11 below.

NTS2609 & NTS2611

a. On the left-hand rear roller assembly, slide all

roller wheels (#3) and plain roller clamps (#6)

toward the center until all slack is removed.

b. Tighten all nuts (#2) on the plain roller clamps (#6)

to the correct torque.

c. On the right-hand rear roller assembly, slide all

roller wheels (#3) and spiked roller clamps (#1A,

#1B, #1C, & #1D) toward the center until all slack

is removed.

d. Continue with step 11 below.

11. Tighten nuts (#2) on roller clamp (#1A) to the correct

torque for a 3/8"-16 GR5 bolt.

12. Rotate clamp (#1B) 60

clockwise from clamp (#1A)

and tighten its nuts (#2) to the correct torque.

13. Rotate clamp (#1C) 60

clockwise from clamp (#1B)

and tighten its nuts (#2) to the correct torque.

14. If included, rotate clamp (#1D) 60

clockwise from

clamp (#1C) and tighten its nuts (#2) to the correct

torque.

15. Restart tractor and raise seeder up. Pull ahead

several feet and lower seeder to the ground.

16. Shut tractor engine off and remove switch key.
17. Store support blocks for future roller wheel

adjustments.

Roller Wheel Adjustment (NTS2609 Shown)

Figure 8-5

73637

Содержание NTS2607















































































Результаты поиска

Содержание NTS2607

Отзывы:

Похожие инструкции для NTS2607

Бренды по названию

Популярные бренды

Land Pride NTS2607, Руководство оператора

Результаты поиска

Содержание NTS2607

Отзывы:

Похожие инструкции для NTS2607

Бренды по названию

Популярные бренды