Land Pride GR1525 Скачать руководство пользователя

Страница: 33 / 44

Section 4: Maintenance & Lubrication

GR1525 Stump Grinder 328-167M

3/17/20

Table of Contents

Carbon Teeth Configuration

Configuration of Carbide Teeth

Viewed From Left Side

Figure 4-2

Refer to Figure 4-2:

The cutting wheel has 30 carbide cutting teeth.

Three are left-hand with straight teeth holders (#5).

Three are right-hand with straight teeth holders (#4).

Twelve are left-hand with bent teeth holders (#3).

Twelve are right-hand with bent teeth holders (#2).

NOTE:

“Right-hand” and “left-hand” designation for

the carbide teeth are determined by standing behind

the tractor and Stump Grinder.

IMPORTANT:

Make certain the teeth are mounted

with the carbide cutting tip leading in rotation.

Mounting a tooth backwards can cause the carbide

tip to pull loose and damage the tooth.

NS FS

FS NS

73207

Carbide Cutting Edge

Must Lead In Rotation

IMPORTANT:

Carbide Cutting Edge Must Lead In Rotation.

The right-hand straight teeth (#4) are attached to the

cutting wheel on the far side (FS) with a series of four

bent teeth (#2) between the straight teeth.
The left-hand straight teeth (#5) are attached to the

cutting wheel on the near side (NS) with a series of

four bent teeth (#3) between the straight teeth.

Straight Tooth Holder & Carbide Tooth

Figure 4-3

Carbide Teeth Maintenance

Refer to Figure 4-3:

The carbide teeth (#4) can be rotated two times before

they need replacing. Once the upper third of the tooth

becomes worn, rotate the tooth as follows:
1. Loosen carbide nut (#1) 3 or 4 full turns. Do not

remove carbide nut.

2. Tap carbide tooth (#4) forward and rotate the head

one-third of a turn to position a non-worn cutting

edge up.

3. Tighten carbide nut (#1) to the correct torque for a

5/16-18 GR5 bolt.

4. Repeat steps 1-3 to rotate the tooth a second time.
5. Once all three outer thirds of the tooth are worn,

replace the carbide tooth as follows:
a. Remove carbide nut (#1) nut spacer (#2), and

worn carbide tooth (#4) from the tooth holder (#3).

b. Inspect carbide nut (#1) and nut spacer (#2) for

wear. Replace nut and spacer as needed.

c. Insert new carbide tooth (#4) in tooth holder (#3).

Make sure the cutting edge is leading in rotation.

d. Install tapered end of nut spacer (#2) leading in

rotation as shown and secure with carbide

nut (#1). Tighten nut to the correct torque for a

5/16-18 GR5 bolt.

73587

Содержание GR1525













































Результаты поиска

Содержание GR1525

Отзывы:

Похожие инструкции для GR1525

Бренды по названию

Популярные бренды

Land Pride GR1525, Руководство оператора

Результаты поиска

Содержание GR1525

Отзывы:

Похожие инструкции для GR1525

Бренды по названию

Популярные бренды