Section 1: Assembly & Set-up
BB4596, BB4510, & BB4512 Pull Type Drag Scraper 306-096M
11/28/18
7
Tractor Requirements
Tractor horsepower should be 70 to 130 horsepower.
Tractors outside the horsepower range must not be used.
Tractor must be capable of controlling the Pull Type Drag
Scraper under all operating conditions.
The number of required hydraulic duplex outlets at the
tractor is dependent upon how the Pull Type Drag
Scraper is set-up.
•
One hydraulic duplex outlet is required if the scraper is
equipped with the standard axle.
•
Two hydraulic duplex outlets are required if the scraper
is equipped with the tilt axle.
Dealer Preparations
This Pull Type Drag Scraper has been partially
assembled at the factory. Additional assembly will be
required before the unit can be attach to the customer’s
tractor. Make sure the intended tractor conforms to the
above.
Assembly Checklist
Check
Page No.
Make sure miscellaneous assembly tools are on hand: Hammer,
alignment punch, assortment of wrenches, and sockets.
Have a forklift or hoist with properly sized chains and safety
stands on hand capable of lifting 2,500 lbs.
Have a minimum of two people available during assembly.
Make sure all major components and loose parts
are shipped with the machine.
Operator’s
Manual
Double check to make sure all fasteners & pins
are installed in the correct location. Refer to the
Parts Manual if unsure.
NOTE:
All assembled hardware from the factory
has been installed in the correct location.
Remember location of a part or fastener if
removed. Keep parts separated.
Parts
Manual No.
306-096P
Make sure working parts move freely, bolts are
tight & cotter pins are spread.
Operator’s
Manual
Make sure customer supplied quick disconnect
adaptors match tractor’s duplex outlets. Quantity
required depends on option selected:
(2) If equipped with standard axle.
(4) If equipped with tilt axle.
Make sure all safety labels are correctly located
and legible. Replace if damaged.
Make sure all red, yellow, and amber reflectors
are correctly located and visible when machine is
in transport position.
Make sure all tires are inflated to the specified psi
air pressure.
Section 8
Page 26
Make sure all wheel bolts are tightened to the
correct torque.
Section 8
Page 26
IMPORTANT:
Your tractor may require additional
ballast to maintain steering control. Refer to your
Tractor’s Operator’s Manual and machine weights
on page 23 to make this determination.
Read and understand the Operator’s Manual. An
understanding of how the unit works will aid in the
assembly and setup.
Be sure to go through the
Pre-Assembly Checklist
before assembling the Pull Type Drag Scraper. Speed up
your assembly task and make the job safer by having all
needed parts and equipment readily at hand.
Torque Requirements
Refer to
“Torque Values Chart”
determine correct torque values when tightening
hardware.
Special Uncrating Instructions
WARNING
!
To avoid serious injury or death:
Always secure heavy components with a hoist or other lifting
device before removing hardware and bands that secure the
components. Heavy components can fall suddenly causing
serious injury or death.
Tongue and Axle Removal
Refer to Figure 1-4 on page 9:
1.
Cut bands securing tongue (#1) and lift tongue from
the crate floor with a lifting hoist.
2. Attach hoist to axle frame (#2) to keep axle frame
from rotating on its wheel(s) while removing
attaching hardware.
3. If tilt cylinder is included, cut zip ties securing tilt
cylinder hydraulic hoses to the scraper frame.
4. Remove bolt and nut (#1). Keep bolt and nut for
reuse during assembly of axle to scraper.
Axle Removal
Figure 1-1
IMPORTANT:
Be sure to retain all uncrating
hardware for assembly and set-up.
30144
Z-Brackets
4
3
2
1
Section 1: Assembly & Set-up
