Land Pride BB0548, Руководство оператора

Страница: 15 / 24

Section 2: Operating Procedures
Table of Contents
2/17/20 BB0548 and BB0554 Fixed Bar Box Scraper 303-187M
11
Section 2: Operating Procedures
Operator’s Responsibilities
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance the Box Scraper. Therefore, it is absolutely
essential that no one operates the Box Scraper unless
they are age 16 or older and have read, fully understood,
and are totally familiar with the Operator’s Manual. Make
sure the operator has paid particular attention to:
•
Important Safety Information , pages 1 to 6
•
Section 1: Assembly & Set-up,
page 8
•
Section 2: Operating Procedures , page 11
•
Section 3: Adjustments
, page 13
•
Section 4: Maintenance , page 14
Perform the following inspections before using your Box
Scraper.
Safety Information
DANGER
!
To avoid serious injury or death:
•
Allow only persons to operate this implement who have
fully read and comprehended this manual, who have been
properly trained in the safe operation of this implement, and
who are age 16 or older. Serious injury or death can result
from the inability to read, understand, and follow
instructions provided in this manual.
•
Make adjustments to the implement after it has been
properly attached to a tractor and secured with solid non-
concrete supports in the up position. Never work around or
under equipment supported by hydraulics. Hydraulics can
drop equipment instantly if controls are actuated or if
hydraulic lines burst even when power to hydraulics is shut
off.
Operating Checklist

Check Page
Inspect tractor safety equipment to make sure
it is in good working condition.
Tractor
Manual
C
arefully raise and lower implement to ensure
drawbar, tires, and other tractor parts do not
make contact with the Box Scraper.
Page 10
Check scraper levelness and pitch.
Refer to “Leveling and Pitch Adjustment”.
Page 13
Check shank depth.
Refer to “Shank Adjustments”.
Page 13
Check cutting blades for wear. Turn blade over
or replace. Refer to “Cutting Blades”.
Page 14
Check shank tips for tightness and wear.
Replace tips as needed. See “Shank Tips”.
Page 14
Check initially and periodically for loose bolts
and pins. See “Torque Values Chart”.
Page 18
Check for worn, bent, broken, loose, &
missing parts. Replace or repair as needed.
Parts
Manual
•
Do not allow anyone near the tractor or implement while
operating. Stop operation if bystanders are too close. They
can be hit by flying projectiles, become entangled in the
equipment, or ran over.
•
Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment
supported by concrete blocks or hydraulics. Concrete can
break, hydraulic lines can burst, and/or hydraulic controls
can be actuated even when power to hydraulics is off.
WARNING
!
To avoid serious injury or death:
•
Never carry riders on the implement or tractor. Riders can
obstruct the operator’s view, interfere with controls, be
pinched by moving components, become entangled in
rotating components, struck by objects, thrown about, fall
off and be run over, etc.
•
Allow only persons to operate this implement who have
fully read and comprehended this manual, who have been
properly trained in the safe operation of this implement, and
who are age 16 or older. Serious injury or death can result
from the inability to read, understand, and follow
instructions provided in this manual.
•
Always keep your body extremities out from under the
shanks and cutting blades while removing, installing, and
adjusting them. It is possible for the cutting blades and/or
shanks to fall causing injury to your body.
•
Do not use implement to tow other equipment unless it is
designed with a tow hitch. Doing so can result in loss of
control and damage the equipment.
•
Do not use implement to lift objects; to pull objects such as
fence posts, stumps, etc; or to push objects. The unit is not
designed or guarded for these uses.
•
Do not use implement as a man lift, work platform or as a
wagon to carry objects. It is not properly designed or
guarded for this use.
•
Perform scheduled maintenance. Check for loose
hardware, missing parts, broken parts, structural cracks,
and excessive wear. Make repairs before putting the
implement back into service.
•
Do not alter implement or replace parts on the implement
with other brands. Other brands may not fit properly or
meet OEM (Original Equipment Manufacturer)
specifications. They can weaken the integrity and impair the
safety, function, performance, and life of the implement.
Replace parts only with genuine OEM parts.
•
Make sure safety labels are in their proper location and are
in good condition before operating the attached implement.
Read and obey all instructions on the labels.