background image

22

TROUBLE

CAUSE

REMEDY

Water in ice bin.

1.  Cold plate drain is obstructed.

1.  Remove obstruction from drain wire.

Noisy/cavitating carbon-
ator pump.

1.  Insufficient incoming water supply pressure.
2.  Loose pump coupling.

1.  Verify incoming supply water pressure to  

carbonator pump is 40 PSI (0.276 MPA) and 
a maximum of 80 PSI (0.552 MPA). Check 
strainer for cleanliness.

2.  Tighten set screw on pump coupling.

TROUBLE

CAUSE

REMEDY

BIB pump does not op-
erate when dispensing 
valve is opened.

1.  Out of CO

2

, CO

2

 not turned on, or low CO

2

 

pressure.

2.  Out of syrup.
3.  BIB connector not tight.
4.  Kinks in syrup or gas lines.

1.  Replace CO

2

 supply, turn on CO

2

 supply, or 

adjust CO

2

 pressure to 30 PSI - 80 PSI (0.207 

MPA - 0.552 MPA).

2.  Replace syrup supply.
3.  Fasten connector tightly.
4.  Straighten or replace lines.

BIB pump operating, but 
no flow.

1.  Leak in syrup inlet or outlet line.
2.  Defective BIB pump.

1.  Replace line.
2.  Replace BIB pump.

BIB pump continues 
to operate when bag is 
empty.

1.  Leak in suction line.
2.  Leaking O-ring on pump inlet fitting.
3.  Defective syrup BIB pump.

1.  Check BIB connector, if still leaking then 

replace line.

2.  Replace O-ring. 
3.  Replace defective pump.

BIB pump fails to restart 
after bag replacement.

1.  BIB connector not on tightly.
2.  BIB connector is stopped up.
3.  Kinks in syrup line.

1.  Tighten BIB connector.
2.  Clean out or replace BIB connector.
3.  Straighten or replace line.

BIB pump fails to stop 
when dispensing valve 
is closed.

1.  Leak in discharge line or fittings.
2.  Empty BIB.
3.  Air leak on inlet line or bag connector.

1.  Repair or replace discharge line.
2.  Replace BIB.
3.  Repair or replace.

To prevent possible harm to the environment from improper disposal, recycle the unit 
by locating an authorized recycler or contact the retailer where the product was  
purchased. Comply with local regulations regarding disposal of the insulation.

Dispenser Disposal

Remote Syrup Pump Troubleshooting

Содержание 23300 Series



































Отзывы: