Lanair DUCTABLE DHI-300 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 52

background image

Section 1 - General Specifications & Hazards

Visit our website at: www.lanair.com

7

Section 14 - Troubleshooting

QUESTIONS?... Contact Customer Service at 1-800-753-1601 M-F 8:00 am- 4:15 pm CST

46

Burner fuel pressure gauge reading hints:

Fuel gauge fluctuates (jumps):

• Suction Line Leak.
• Air in fuel, refer to Troubleshooting Chart Item B.
• Quad ring seal for the nozzle may be damaged.
• Seal in adapter block may be worn or damaged.
• Fuel pressure regulator seal leaking or dirty.
• Suction line strainer plugged or dirty.

• Dirty Pump Screen

Reading gradually decreases:

• Fuel pump output decreasing.
• Fuel viscosity decreasing.
• Orifice in nozzle is wearing.

• Dirty Pump Screen

Reading gradually increases:

• Fuel pump output increasing.
• Fuel viscosity increasing (cold fuel, and/or gear lube).
• Orifice in nozzle is becoming plugged.

Reading drops to –0- PSI when the burner is off.

• Dirt between the diaphragm and the seat in the by-pass regulator.
• Dirt between the plunger and the nozzle seat.
• Leak in the plumbing connections.
• Leak in the pre-heater assembly (damaged or missing o ring).
• Fuel pre-heater switch is off.

Steps to check the air operated fuel valve:

•

Disconnect the two transformer wires from the terminal block in the burner.

• Jump the cad cell circuit (refer to page 43).
• Disconnect the fuel supply pump orange wire from the terminal block inside the

burner.

• Set the dial indicator as shown on the diaphragm piston.
• Zero the dial indicator.
• Start the burner so that the air valve opens.

NOTE:

The dial indicator should read +.015 to .050, which references the diaphragm piston

travel.

FRONT

REAR

LEFT SIDE

RIGHT SIDE

8" exhaust

View port

Fan Hi-Limit
switch

Clean Out

Access Panel

Blower Moter

Assembly

Electrical Access
Panel

Power Box

Burner
Assembly

«
...
44
45
46
47
48
...
»

Содержание DUCTABLE DHI-300





















































Отзывы:

Нет отзывов

Похожие инструкции для DUCTABLE DHI-300

Бренд: Water Worker Страницы: 2

Бренд: A.O. Smith Страницы: 65

Бренд: DAY Страницы: 51

SMART ECG 1000 A

Бренд: Airtecnics Страницы: 22

Бренд: EQUATION Страницы: 34

Бренд: Somogyi Elektronic Страницы: 20

Бренд: Hamtronix Страницы: 16

Бренд: L.B. White Страницы: 16

PROFESSIONAL OHIR18LV

Бренд: Dyna-Glo Страницы: 6

Бренд: Talhu Oy Страницы: 11

Бренд: UNITED Страницы: 5

Citara T PLUS Series

Бренд: Vasner Страницы: 28

Бренд: Wacker Neuson Страницы: 68

Бренд: Twin-Star International Страницы: 12

Бренд: Heat Controller Страницы: 43

Бренд: CAC / BDP Страницы: 18

RADIO TIMING NETWORK DCF

Бренд: Gorgy Timing Страницы: 50

Бренд: Airrex Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды