Lanair DUCTABLE DHI-300 Скачать руководство пользователя страница 45

Страница: 45 / 52

Section 1 - General Specifications & Hazards

QUESTIONS?... Contact Customer Service at 1-800-753-1601 M-F 8:00 am- 4:15 pm CST

OPTIONAL J-PUMP

No.

Description

Pump Platform

Pump Motor

Pump Guard

Pump

Pressure Gauge port

Easy Flow Bleed Valve

1/4" NPT Inlet

(1/2" J Pump)

1/8" NPT Outlet

(1/4" J Pump)

Pump coupler

Pump Assembly-

Performance Ratings

Voltage . . . . . . . . . . . . . . . . . . . . . . 115 vac

Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . 60 hz

Weight . . . . . . . . . . . . . . . . . . . . . . . . . 24 lbs

Pump Motor . . . . . . . . . . . . . . . . . . 5 amps

Section 14 - Troubleshooting

Visit our website at: www.lanair.com

• Install a jumper wire between the two F-F

terminals.

• Push reset button for 2 seconds.
• Turn room thermostat up so that it calls for

heat.

• Disable the air operated fuel valve.
• To activate the oil primary

momentarily

dis

connect one end of the jumper wire on the
F-F terminals. The burner will attempt to fire.

IMPORTANT

remove the jumper wire when

testing is complete, and replace the cad cell
wires.

Do not run the heater with the cad cell

wires disconnected.

Disabling the air operated fuel valve.

Note:

Most trouble shooting tests will require the air operated fuel valve to be disabled, to

do this:

• Adjust the heater air filter/regulator to -0- PSI.

Install jumper wire

Vacuum Gauge reading hints:

No reading 0-1 HG

• Pump not operating.
• Pump air locked and needs priming. Refer to section 10.
• Vacuum leak:

Pump shaft seal

Pump cover gasket

Suction strainer gaskets

Low fuel level in tank

Pipe connections suction side

Strainer in pump cover

Low to normal reading, 1-6 inches HG.

•

Pump operating properly.

• Fuel being used has a low viscosity.

• Fuel oil is being used.

• Fuel is at room temperature (warm).

• High level of gasoline in the fuel (use approved fuels only).

High reading, 7 inches of HG, or more.

• Fuel being used has to high of a viscosity. • Suction line strainer dirty or plugged.
• Fuel is too cold.

• Check valve installed wrong or stuck.

• Fuel contains gear lubes (use approved fuels only).

Reading fluctuates (jumps).

• Vacuum leaks in the suction side of the piping to the pump.
• Low fuel level in the tank.

Содержание DUCTABLE DHI-300





















































Результаты поиска

Содержание DUCTABLE DHI-300

Отзывы:

Похожие инструкции для DUCTABLE DHI-300

Бренды по названию

Популярные бренды

Lanair DUCTABLE DHI-300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DUCTABLE DHI-300

Отзывы:

Похожие инструкции для DUCTABLE DHI-300

Бренды по названию

Популярные бренды