Lanair DUCTABLE DHI-300 Скачать руководство пользователя страница 34

Страница: 34 / 52

Section 7 - Air Supply Installation

Visit our website at: www.lanair.com

General Requirements

Install an air pressure supply line connection to the air filter/regulator on the rear of the
heater.

The air supply source must be capable of producing 2.0 CFM @ 60 PSI.

Install a shut off valve in the air supply line for service.

Install a primary air filter/regulator with a gauge (capable of reading line pressure) in the
air supply line prior to the air filter/regulator mounted on the furnace. The primary air fil-
ter/regulator is

not supplied

with the furnace.

If the primary air regulator does not have a filter with a bowl, a condensate drain leg
must be installed in the air supply line.

Install a quick disconnect at the air filter/regulator on the furnace for service.

For the ease of installation install a flexible air line (.250 I.D. minimum) from the quick
disconnect to the primary air regulator.

The air supply line must be pitched uphill from the primary regulator to the furnace to
prevent condensation from entering your burner.

Open all air shut off valves, and set the primary air regulator at 30 PSI.

10.

Set the air filter/regulator on the front of the furnace to 15 LBS. See illustration below
(Fig. 5) for a typical air pressure supply installation.

Figure 5

Section 13 - Service / Maintenance

QUESTIONS?... Contact Customer Service at 1-800-753-1601 M-F 8:00 am- 4:15 pm CST

Maintenance - Air Pre-Heater

Remove Pre-Heater Assembly

• Disconnect the air line from the

brass fitting on the air pre-heater
and then from

the air solenoid and remove.

• Disconnect wiring from the oil pre-

heater cartridge, air pre-heater
cartridge and snap disc assembly in
the wiring junction box.

• Disconnect fuel line and fitting (6)

from the oil block (5).

• Disconnect fuel pressure gauge (8)

and fitting from the oil block (5).

• Remove button hex screw (14) and

washer (11).

• Lift pre-heater assembly and care

fully pull straight back. Remove
entire assembly from the burner.

• Remove ignitor assembly (6).

2. Remove Diaphragm Assembly

from Air Pre-Heater

• Carefully place pre-heater assembly

in a vice.

NOTE:

Do not damage

pre-heater.

• Unscrew diaphragm assembly (19)

from air pre-heater and set aside.
Remove o-ring and discard.

3. Remove Adapter Assembly

• Remove hex cap screws (17) and set adapter

assembly aside.

4. Remove Plunger , Spring and Cartridge Heater

• Remove spring (13) from plunger (15) and discard.
• Using a hook or screwdriver, carefully remove Viton

insert (14) and discard.

• Remove and discard 1/4" o-ring (10) and 11/16" o-

ring (11).

• Loosen and remove cartridge heater and set aside.

5. Remove Nozzle Assembly and Quad Ring

• Remove nozzle assembly (3) using a 9/16" wrench.
• If quad ring (4) does not come out with nozzle, care

fully remove it and discard.

Ref.

Part

No.

Qty.

Description

9853

turbulator

7004

set screw

9757

nozzle Heater 260/300

9870

quad ring (K)

9814

air pre-heater block

3730

ignitor assembly

9870

hex cap screw *

7418

flat washer

3726

connector

9870

1/4" o-ring *

9870

11/16" o-ring *

9856

air cartridge heater

9870

spring *

9870

Viton insert *

9835

plunger

9838

Adapter block assembly

9870

hex head cap screw *

9871

1/2" o-ring (K)

9871

diaphragm assembly **

9871

hex head cap screw **

oil pre-heater block

* contained in tune up kit 9870

** contained in tune-up kit 9871

Remove wires from the block by
inserting a flat tip screwdriver into the
top slot. Push tip all the way down
and carefully push forward. Remove
wire.

Содержание DUCTABLE DHI-300





















































Результаты поиска

Содержание DUCTABLE DHI-300

Отзывы:

Похожие инструкции для DUCTABLE DHI-300

Бренды по названию

Популярные бренды

Lanair DUCTABLE DHI-300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DUCTABLE DHI-300

Отзывы:

Похожие инструкции для DUCTABLE DHI-300

Бренды по названию

Популярные бренды