background image

 

6

DMX512 specifications 

 

The projector reads 6 consecutive DMX 

DMX Ch. 

FUNCTION 

 channels starting from the set address. 

Dimmer 

 2 

Shutter/Strobe 

The AUX channel always works as rainbow 

Cyan 

control channel and if REMOTE CONTROL 

Magenta 

is active (INDEX 5) also it works as remote 

Yellow 

control channel 

Rainbow or Remote control 

 

(ch. 1) Dimmer 

 

Controls the intensity of the light beam from 0 to 100%. It also works during the Strobe function. 
The value of this channel is ignored if the shutter channel is in the CLOSE position. 
 

Function 

DMX Values 

Notes 

Open 252..255 

 

Proportional 

4..251 

Intensity Min ... Max  

Close 0..3  
 

(ch. 2) Shutter/Strobe 

 

Selects blackout, channel open and strobe functions.  
With the SHUT ON COLOUR function selected, the shutter closes during the colour change. 
 

Function 

DMX Values 

Notes 

Open 248..255 

 

Close 

240..247 

Blackout (It has priority over the dimmer) 

Strobe 29 

232..239 

Maximum rate (1 flash/sec) 

Strobe 28 

224..231 

 

Strobe 27 

216..223 

 

Strobe 26 

208..215 

 

Strobe 25 

200..207 

 

Strobe 24 

192..199 

 

Strobe 23 

184..191 

 

Strobe 22 

176..183 

 

Strobe 21 

168..175 

 

Strobe 20 

160..167 

 

Strobe 19 

152..159 

 

Strobe 18 

144..151 

 

Strobe 17 

136..143 

 

Strobe 16 

128..135 

 

Strobe 15 

120..127 

 

Strobe 14 

112..119 

 

Strobe 13 

104..111 

 

Strobe 12 

96..103 

 

Strobe 11 

88..95 

 

Strobe 10 

80..87 

 

Strobe 9 

72..79 

 

Strobe 8 

64..71 

 

Strobe 7 

56..63 

 

Strobe 6 

48..55 

 

Strobe 5 

40..47 

 

Strobe 4 

32..39 

 

Strobe 3 

24..31 

 

Strobe 2 

16..23 

 

Strobe 1 

8..15 

Minimum rate 

Close 

0..7 

Blackout (It has priority over the dimmer) 

 

Содержание PROLUM D3














Отзывы: