manualshive.com logo in svg

Lampo PROLUM D3, Руководство пользователя

Поделиться
Скачать
Lampo PROLUM D3 Скачать руководство пользователя страница 2

 

1

 
BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE 
INSTRUCTIONS IN THIS MANUAL. 
 
QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE 
INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR. 
 
BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE 
VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR. 
 
FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO: 
 

[email protected] 

 
 
 
 

SOLID: Objects exceeding 12mm diameter 

    WATER: 

Non 

protected 

 
 

 

 

 

Not suitable for direct mounting on normally flammable surfaces 

 
 

Minimum distance from lighted objects (meters) 

 

 

Rated maximum ambient temperature (indoor with ventilation) 

 
 

Connection must be made to a power supply system fitted with efficient 
earthing (EN60598-1 – Class I fixture) 

 
 

Replace any cracked protective shield, dichroic filter or lens 

 
 

Ignitor circuit lamp have very high voltage 

 

 
 
 
 

Index 

 

Dimensions and weight  ----------------------------------------------------------------------------------  page 2 
Technical data  ---------------------------------------------------------------------------------------------  page 2 
Storage  ------------------------------------------------------------------------------------------------------ page 3 
Admissible environmental conditions -----------------------------------------------------------------  page 3 
Power supply  ----------------------------------------------------------------------------------------------  page 3 
Example of connection  ----------------------------------------------------------------------------------  page 4 
DMX signal cable  -----------------------------------------------------------------------------------------  page 4 
DMX512 specifications  ----------------------------------------------------------------------------------  page 6 
User’s interface  -------------------------------------------------------------------------------------------  page 8 
Parameters of projector  --------------------------------------------------------------------------------  page 9 
Stand alone mode (Recordable dmx scenes)  --------------------------------------------------------  page 10 
Remote control of parameters  ------------------------------------------------------------------------- page 11 
Lamp replacement  ---------------------------------------------------------------------------------------  page 12 
Lamp calibration  ------------------------------------------------------------------------------------------ page 12 

 

Содержание PROLUM D3














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды