■
Type selection method
Cautions for operation
the symptom of troubles. It is prohibited to use this mechanism at the temperature exceeding the specifi ed range. It is not permitted to apply this
mechanism for the cabinet installing a heat-generating microwave oven or other similar appliances.
It is necessary to periodically check the fi xing screws for loosing. Tighten the loosed screws as required.
Keep a door from forced opening and closing. It is prohibited to open a door over a full open angle or to close a door with excess force.
●
The working temperature range of this mechanism is 0~40°C. Opening and closing speed of the door depends on the temperature.This is not
●
Be careful not to insert a fi nger into the arm mechanism of the unit. Sever injury may be caused.
●
●
The right-hand and left-hand side bodies of this mechanism should be installed in set.
●
This is the mechanism exclusively for a fl ap type door application. Be reminded that we can not take the responsibility for damages and injuries caused
by other applications, disassembly, conversion and the application to the door exceeding the standard ranges shown in the item ”Type selection meth-
od”.
●
This mechanism must be installed to the cabinet correctly in accordance with the indications of this manual. Notice that the non-observance of the
specifi ed dimensions not only does not enable this mechanism to show its full performance, but also may result in damage and also cause injury.
●
It is necessary to use the attached screws for installing this mechanism. Otherwise the disconnection of this mechanism may happen causing injury.
●
For improvement the specifi cation may be changed without notice. As for details please verify the actual goods.
●
The applicable door must have the construction for which it is diffi cult to induce bent or torsion.
Any failure to observe the following cautions may result in personal injury and property damage.
CAUTION
Cautions for installation
※
Screws for fixing
mounting plate are NOT
included.
Prepare 2 pcs of screw
separately. (M3.5~4 is recommended.)
Parts for installing to 20mm width aluminum frame door
7
5
Bind tapping screw
(3.5x15) 4pcs
6
4
HDSN-SZ mounting
plate 1pc
Truss screw (M4x6)
1pc
1
8
HDSN-AZ mounting
plate 1pc
Parts of separate packing (Select either)
HDSN-30 body / left-hand side 1pc
2
Body mounting plate 1pc
3
Bind tapping screw
(3.5x15) 3pcs
Truss screw (M4x6)
1pc
ＰＡＴ．Ｐ
Ｒ
1
HDSN-30 body / right-hand side 1pc
2
Body mounting plate 1pc
3
Bind tapping screw
(3.5x15) 3pcs
ＰＡＴ．Ｐ
Ｒ
Parts for installing to solid wooden door
or 45mm width aluminum frame door
Option
Option
2 pcs
The slide hinge (overlay use, non-catch type) should be used as a
door- hanging device.
The LAMP brand 230 series slide hinge (product No. 230-26/19T,
non-catch type) is recommended.
Fig.2.Cabinet
Ｈ
Ｔ
Ｗ
1
0
Ｗ
0
HDSN-30
HEAVY - DUTY SOFT - DOWN STAY
INSTALLATION MANUAL
Read this manual carefully for proper installation and operation.
Incorrect installation and improper use of the product may cause damage to the unit and also cause injury.
This manual should be kept by the user after installation.
Fig. 1. Part description
■
Part description
Calculate the door torque according to the following formula considering the weight and the
height of the applicable door. Select the suitable type as per Table 1.
※
Contact our sales representatives in case of installing to a cabinet exceeding the
indicated ranges.
Door height H (m) /2 x Door weight (kg) x 9.8 = Door torque (N
・
m)
Table 1. Type and suitable door range
Door torque
Opening angle 90°
Type
Opening angle 80°
H D S N - 3 0 K R
H D S N - 3 0 K L
H D S N - 3 0 M L
H D S N - 3 0 M R
H D S N - 3 0 H L
H D S N - 3 0 S R
H D S N - 3 0 S L
H D S N - 3 0 H R
13.7
〜
17.5 N
・
m ( 140
〜
179 kgf
・
cm ) / pair
17.6
〜
21.5 N
・
m ( 180
〜
219 kgf
・
cm ) / pair
21.6
〜
25.4 N
・
m ( 220
〜
259 kgf
・
cm ) / pair
25.5
〜
29.4 N
・
m ( 260
〜
300 kgf
・
cm ) / pair
13.7
〜
19.5 N
・
m ( 140
〜
199 kgf
・
cm ) / pair
19.6
〜
24.4 N
・
m ( 200
〜
249 kgf
・
cm ) / pair
24.5
〜
29.3 N
・
m ( 250
〜
299 kgf
・
cm ) / pair
29.4
〜
34.3 N
・
m ( 300
〜
350 kgf
・
cm ) / pair
●
Make sure that installation position and specifications are followed. Unsuitable installation position may damage the mechanism when in case two
stays are used together.
●
Make sure that the arm of the stay is parallel with the side panel of the cabinet.
Sugatsune guarantees the quality of this product as for all its parts. It cannot however guarantee the final
assembly as a whole.
This product was manufactured and delivered with our utmost care. Should you however find any defect,
please contact your dealer immediately.
Sugatsune warrants that this product is free from defect for a period of one (1) year from the date of
delivery.
Sugatsune liability is limited to the replacement of this product by a similar one free of defect. In no case
does this extend to the replacement of the installation or the cabinet as a whole.
