background image

Lake Shore Model 234/234D User’s Manual 

 

 

LIMITED WARRANTY STATEMENT – WARRANTY PERIOD: ONE (1) YEAR 

1.

 

Lake Shore warrants that this Lake Shore product (the “Product”) will be free from defects in materials 
and workmanship for the Warranty Period specified above (the “Warranty Period”). If Lake Shore 
receives notice of any such defects during the Warranty Period and the Product is shipped freight 
prepaid, Lake Shore will, at its option, either repair or replace the Product if it is so defective without 
charge to the owner for parts, service labor or associated customary return shipping cost. Any such 
replacement for the Product may be either new or equivalent in performance to new. Replacement or 
repaired parts will be warranted for only the unexpired portion of the original warranty or 90 days 
(whichever is greater). 

2.

 

Lake Shore warrants the Product only if it has been sold by an authorized Lake Shore employee, sales 
representative, dealer or original equipment manufacturer (OEM). 

3.

 

The Product may contain remanufactured parts equivalent to new in performance or may have been 
subject to incidental use. 

4.

 

The Warranty Period begins on the date the Product ships from Lake Shore’s plant. 

5.

 

This limited warranty does not apply to defects in the Product resulting from (a) improper or inadequate 
maintenance, repair or calibration, (b) fuses, software and non-rechargeable batteries, (c) software, 
interfacing, parts or other supplies not furnished by Lake Shore, (d) unauthorized modification or 
misuse, (e) operation outside of the published specifications or (f) improper site preparation or 
maintenance. 

6.

 

To the extent allowed by applicable law, the above warranties are exclusive and no other warranty or 
condition, whether written or oral, is expressed or implied. Lake shore specifically disclaims any implied 
warranties or conditions of merchantability, satisfactory quality and/or fitness for a particular purpose 
with respect to the product. Some countries, states or provinces do not allow limitations on an implied 
warranty, so the above limitation or exclusion might not apply to you. This warranty gives you specific 
legal rights and you might also have other rights that vary from country to country, state to state or 
province to province. 

7.

 

To the extent allowed by applicable law, the remedies in this warranty statement are your sole and 
exclusive remedies. 

8.

 

Except to the extent prohibited by applicable law, in no event will lake shore or any of its subsidiaries, 
affiliates or suppliers be liable for direct, special, incidental, consequential or other damages (including 
lost profit, lost data or downtime costs) arising out of the use, inability to use or result of use of the 
product, whether based in warranty, contract, tort or other legal theory, and whether or not lake shore 
has been advised of the possibility of such damages. Your use of the Product is entirely at your own 
risk. Some countries, states and provinces do not allow the exclusion of liability for incidental or 
consequential damages, so the above limitation may not apply to you. 

9.

 

Except to the extent allowed by applicable law, the terms of this limited warranty statement do not 
exclude, restrict or modify, and are in addition to, the mandatory statutory rights applicable to the sale 
of the product to you. 

CERTIFICATION 

Lake Shore certifies that this product has been inspected and tested in accordance with its published 
specifications and that this product met its published specifications at the time of shipment. The accuracy and 
calibration of this product at the time of shipment are traceable to the United States National Institute of 
Standards and Technology (NIST); formerly known as the National Bureau of Standards (NBS), or to a 
recognized natural standard. 

TRADEMARK ACKNOWLEDGEMENT 

Manufacturers and sellers claim many designations as trademarks to distinguish their products. Where those 
designations appear in this manual and Lake Shore was aware of a trademark claim, the designations appear 
in initial capital letters with a ™ or 

®

 symbol. 

Apiezon

®

 is a trademark of Biddle Instruments. 

CalCurve™, Carbon-Glass™, Cernox™, Duo-Twist™, High-Temperature Cernox™, Quad-Lead™, 

Quad-Twist™, Rox™, SoftCal™, and Thermox™ are trademarks of Lake Shore Cryotronics, Inc. 

Teflon

®

 is a trademark of DuPont De Nemours. 

 

Copyright © 1993, 1995, 1997, 1999, 2003-04, 2009, and 2016 by Lake Shore Cryotronics, Inc. All rights 
reserved. No portion of this manual may be reproduced, stored in a retrieval system, or transmitted, in any 
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the express 
written permission of Lake Shore. 

Содержание 234


















































Отзывы: