Laird ConnexLink CL2510 Скачать руководство пользователя

Страница: 18 / 28

www.lairdtech.com

Laird Technologies

CL2510

RF Transceiver

An example of an acceptable non-standard baud rate being accepted is shown in the following graphic:

Acceptable Baud Rate Found

No Acceptable Baud Rate Found

Clicking the Save button will cause the baud rate shown in the Actual Baud Rate window to be displayed in the

Baud window on the Configure tab of the application. Clicking Cancel will ignore these changes. The Actual
Baud Rate will not always match the Desired Baud Rate. However, the program verifies that the Desired Baud

Rate is within 3% of the Actual Baud Rate (as required by the radio).

Hex/Decimal Button

All of the text entry type boxes found on the Configure tab have an indication of whether the value is

presented in Hexadecimal (Hex) or Decimal (Dec). The indication (Hex or Dec) can be clicked to toggle
between Hexadecimal and Decimal notation.

GUI View Button

Clicking the GUI View Button enables a GUI representation of the 256 byte EEPROM contents of the radio.

CONFIgURATION
SOFTWARE
OVERVIEW

Содержание ConnexLink CL2510





























Результаты поиска

Содержание ConnexLink CL2510

Отзывы:

Похожие инструкции для ConnexLink CL2510

Бренды по названию

Популярные бренды

Laird ConnexLink CL2510, Руководство пользователя

Результаты поиска

Содержание ConnexLink CL2510

Отзывы:

Похожие инструкции для ConnexLink CL2510

Бренды по названию

Популярные бренды