background image

Hazard levels

Hazard level

Indication

DANGER:

 

A hazardous situation which, if not avoided, will result in

death or serious injury

WARNING:

 

A hazardous situation which, if not avoided, could result

in death or serious injury

CAUTION:

 

A hazardous situation which, if not avoided, could result

in minor or moderate injury

NOTICE:

 

• A potential situation which, if not avoided, could

result in undesirable conditions

• A practice not related to personal injury

Hazard categories

Hazard categories can either fall under hazard levels or let specific symbols replace the
ordinary hazard level symbols.
Electrical hazards are indicated by the following specific symbol:

Electrical Hazard:

 

These are examples of other categories that can occur. They fall under the ordinary
hazard levels and may use complementing symbols:

• Crush hazard
• Cutting hazard
• Arc flash hazard

User safety

General safety rules

These safety rules apply:

• Always keep the work area clean.
• Pay attention to the risks presented by gas and vapors in the work area.
• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash

hazards.

• Always bear in mind the risk of drowning, electrical accidents, and burn injuries.

Safety equipment

Use safety equipment according to the company regulations. Use this safety equipment
within the work area:

• Hard hat
• Safety goggles, preferably with side shields
• Protective shoes
• Protective gloves
• Gas mask
• Hearing protection

Introduction and Safety

Laing Thermotech ACT-4 wireless Potable Hot Water Recirculation Kit Installation, Operation and Maintenance
Manual

3

Содержание ACT-4

























Отзывы: